Portfolio
191 structures, built or quoted here
These are real structures. Each one came through this company as a built job, a quoted enquiry or a design from our own office, and each is rendered from its own geometry. The names are generic because a customer's design is the customer's: what you can see is the steel, the size and the group it belongs to.
The published models
Showing 191 of 191Showing 57 of 191Showing 25 of 191Showing 19 of 191Showing 19 of 191Showing 39 of 191Showing 32 of 191
Nothing here is a photograph, a stock image or a generated picture. Each tile is a render of the structure's own geometry in raw steel, on the same camera and the same light as every other picture on this site. No customer, machine designation, drawing number or project is named, and no model file is served from this site: what leaves the server is pixels.
Machine frames and weldments
Tubular space frame chassis, 10.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A tubular space frame chassis built from square hollow section rails and cross braces, with flat plated deck sections and four curved, plated wheel arches running along its length. One end carries a tall, multi-level tube cage with mounting brackets and lugs, the other stays low and open. It measures about 10.4 m long, 2.5 m wide and 2.1 m high. Such parts are tack welded on a fixture and welded out, then checked against the drawing with the measuring arm.
- Length, width and height
- 10 447 x 2 487 x 2 132 mm
- 10 447 x 2 487 x 2 132 mm. Longest dimension 10 447 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Welded main frame, 9.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded main frame built from two long box rails tied together by a cross tower, with plate webs, gusset ribs and bolt lugs along its length. One end carries a machined bearing plate with a bored seat, the other a bracketed pivot with stiffening ribs and mounting holes. It measures about 9.5 m long, 1.2 m wide and 1.6 m high. In this hall a part like this is set on a fixture, tacked and welded out, then bored and faced on the boring mill.
- Length, width and height
- 9 486 x 1 190 x 1 562 mm
- 9 486 x 1 190 x 1 562 mm. Longest dimension 9 486 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Logistics frame assembly, 13.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A long closed box girder, plated flush on every side with welded corner seams running the full length. A small bracket sits near one end on the top plate, with a cut opening nearby, the only break in the plain, continuous box form. It measures about 13.6 m long, 2.6 m wide and 2.8 m high. Pieces like this are tack welded on a fixture and welded out and welded on the robotic track or by hand.
- Length, width and height
- 13 620 x 2 551 x 2 800 mm
- 13 620 x 2 551 x 2 800 mm. Longest dimension 13 620 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Machine frame weldment, 9.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machine base frame built from plated side walls, folded box sections and a ribbed floor, with an open top and a large round bearing bore through the central bulkhead. Stiffening ribs step down the lower chamber, with brackets, lugs and small pads set along the edges. It measures about 9.3 m long, 2.5 m wide and 2.8 m high. Here a part like this is tacked up on a fixture and welded through, with the bores and pads machined after welding.
- Length, width and height
- 9 282 x 2 500 x 2 830 mm
- 9 282 x 2 500 x 2 830 mm. Longest dimension 9 282 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Portal frame weldment, 6.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A portal frame weldment built from tapered box section arms joined at a flat plate crown, with small brackets and lugs along the top and a braced linkage frame hanging under one arm. The sloped arm ends in a bored pivot eye, stiffened by a row of gussets at the open end. It measures about 6.4 m long, 2.7 m wide and 1.9 m high. Parts like this are tack welded on a fixture and welded out, with every bore and pad cut after welding.
- Length, width and height
- 6 437 x 2 730 x 1 869 mm
- 6 437 x 2 730 x 1 869 mm. Longest dimension 6 437 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Machine bed frame, 6.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machine bed frame built from two long box-section top rails carried on rows of square-section legs with bolted foot plates, tied together by cross members and a lower rail down each side. The top rails carry a pale machined strip along their full length, giving a flat bearing face for mounting equipment. It measures about 6.3 m long, 1.9 m wide and 1.0 m high. In this hall a part like this is welded on the 14 m robotic track for a series, by hand for a one-off.
- Length, width and height
- 6 304 x 1 850 x 955 mm
- 6 304 x 1 850 x 955 mm. Longest dimension 6 304 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Welded machine frame, 5.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded machine base frame built as a long plated box, with side walls, a top deck plate and internal ribs between them. Rectangular cut-outs run along both side walls, a low platform extends at each end, and a hinged access hatch sits at one corner, with four lifting lugs on the deck for handling. It measures about 5.5 by 1.8 m and stands 1.3 m high. A part like this is cut from plate on the laser bed and tack welded on a fixture and welded out.
- Length, width and height
- 5 500 x 1 769 x 1 274 mm
- 5 500 x 1 769 x 1 274 mm. Longest dimension 5 500 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Reel stand weldment, 3.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A reel stand weldment made from two stacked plated box sections on a sloped, rib-stiffened base, carried on two long beam feet joined by cross bars and footplates. A large round bore through the upper box, triangular stiffening ribs on the sloped face, a rear access opening and top lifting lugs stand out. It measures about 3.5 m long, 2.3 m wide and 2.3 m high. Parts like this are welded out on a fixture, with the bores and pads machined after welding.
- Length, width and height
- 3 490 x 2 260 x 2 267 mm
- 3 490 x 2 260 x 2 267 mm. Longest dimension 3 490 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Lift frame with guard grille, 3.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A lift frame built around two curved cheek plates set at a kinked angle, with a row of straight grille bars spanning the opening between them. Pivot lugs with bored eyes sit at both ends, a cylindrical bore runs along one arm, and small mounting lugs sit on the cheek faces. It measures about 3.3 m long, 2.2 m wide and 1.5 m high. A part like this is tack welded on a fixture and welded out, with the bores and pads machined after welding.
- Length, width and height
- 3 270 x 2 160 x 1 515 mm
- 3 270 x 2 160 x 1 515 mm. Longest dimension 3 270 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Subframe with cross members, 6.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A long subframe built from two parallel rails joined by regular cross members, with a boxed end section and a lighter open frame at the other end. Rows of small mounting brackets line both outer rails, with a couple of upright locating pins standing near each end. It measures about 6.9 m long, 1.2 m wide and 0.4 m high. Pieces like this are welded out on a fixture, with the bores and pads machined after welding.
- Length, width and height
- 6 940 x 1 157 x 383 mm
- 6 940 x 1 157 x 383 mm. Longest dimension 6 940 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Welded side plate with stiffeners, 6.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded side plate forms a long edge-standing panel, with horizontal ribs across the back and short flange tabs folded along the top. Two rows of square cut-outs run the length for access and weight saving, with an arched cut-out near one end and bolt holes along both edges. It measures about 6.9 m long, 0.2 m wide and 1.5 m high. Pieces like this are laser cut up to 20 mm and welded on the robotic track or by hand.
- Length, width and height
- 6 915 x 210 x 1 455 mm
- 6 915 x 210 x 1 455 mm. Longest dimension 6 915 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Rectangular box section frame, 6.8 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A rectangular box section frame built as a long, flat outer ring of deep welded box sections, with a lighter inner ledge strip running its full length and small pad plates spaced along the top edges. The open centre and flat pad faces stand out, set to carry mounted equipment. It measures about 6.8 m long, 2.5 m wide and 0.5 m high. Here a part like this is set on a fixture, tacked and welded out, with every bore and pad cut after welding.
- Length, width and height
- 6 782 x 2 485 x 475 mm
- 6 782 x 2 485 x 475 mm. Longest dimension 6 782 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Plate girder with drilled flanges, 6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A plate girder built from a tall web plate between a drilled top and bottom flange running the full length, stiffened by vertical ribs on the back face. Small lifting tabs sit along the top edge, and end plates close off both faces. It measures about 6.0 m long, 0.4 m wide and 1.2 m high. A piece like this is laser cut up to 20 mm, tack welded on a fixture and welded out, with the bores and pads machined after welding.
- Length, width and height
- 6 020 x 420 x 1 165 mm
- 6 020 x 420 x 1 165 mm. Longest dimension 6 020 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Flat machine frame, 6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A flat machine frame made of box section rails and uprights, standing on its narrow edge. Four long horizontal rails tie into two vertical posts, braced by cross members, with end plates and bolt holes closing the rail ends. Two short stub columns rise above the top rail. It measures about 6.0 m long, 0.3 m wide and 3.4 m high. A part like this is set on a fixture, tacked and welded out, with the bores and pads machined after welding.
- Length, width and height
- 5 994 x 310 x 3 446 mm
- 5 994 x 310 x 3 446 mm. Longest dimension 5 994 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Lattice girder frame, 5.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A lattice girder frame formed from two parallel box-section girders with diagonal bracing, tied together by cross beams across the top to close out a rigid box structure. One end carries thick drilled end plates and flange pads with bolt patterns, with projecting brackets at the corners for connection. It measures about 5.7 m long, 2.0 m wide and 1.2 m high. A piece like this is welded out on a fixture, with every bore and pad cut after welding.
- Length, width and height
- 5 690 x 1 980 x 1 230 mm
- 5 690 x 1 980 x 1 230 mm. Longest dimension 5 690 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Ladder chassis frame, 5.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A ladder chassis frame of this kind is formed from two long rails tied together by cross members, with boxed ends, gusseted brackets and a dropped mounting assembly hung under the middle. Rows of bored holes and small welded lugs line the rails for fittings. The boxed end plates and the stepped bracket under the centre stand out most. It measures about 5.6 by 1.2 by 0.8 m. A piece like this is tacked up on a fixture and welded through, with every bore and pad cut after welding.
- Length, width and height
- 5 590 x 1 195 x 797 mm
- 5 590 x 1 195 x 797 mm. Longest dimension 5 590 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Base frame with lifting lugs, 4.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A base frame of this kind is a long welded box built from steel plate, with a drilled top plate, ribbed side walls carrying window cutouts, and a lower stepped platform extending from each end. Four lifting eyes sit at the top corners, and a machined pocket with bolted pads breaks one end step. It measures about 4.7 by 1.5 m, standing 1.3 m high. Pieces like this are set on a fixture, tacked and welded out, then bored and faced on the boring mill.
- Length, width and height
- 4 655 x 1 469 x 1 274 mm
- 4 655 x 1 469 x 1 274 mm. Longest dimension 4 655 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Box girder, 4.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded steel box girder, built from plate into a long rectangular section with a stepped drop bracket, a downward lug, a bored web and a machined top face along part of its length. A notched fin at one end and a row of edge stiffeners stand out. It measures about 4.5 m long, 0.3 m wide and 1.1 m high. Such parts are welded by hand or on the 14 m robotic welding track, with every bore and pad cut after welding.
- Length, width and height
- 4 550 x 261 x 1 069 mm
- 4 550 x 261 x 1 069 mm. Longest dimension 4 550 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Welded base frame with web plates, 4.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A long welded base frame built from hollow section legs and top rails, with a slatted rib floor at one end and plated floor pans at the other, split by an internal partition. A small raised box with a flat top pad sits near the middle, with footplates along both sides. It measures about 4.5 m long, 1.4 m wide and 0.5 m high. A part like this is tack welded on a fixture and welded out and welded on the robotic track or by hand.
- Length, width and height
- 4 480 x 1 430 x 530 mm
- 4 480 x 1 430 x 530 mm. Longest dimension 4 480 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Carrier frame with cross members, 4.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A carrier frame built from two deep box section side rails, their webs punched with long rows of drilled holes, linked by three box cross members and a lighter diagonal lower rail pair. Short stub ends and small mounting lugs project at each corner. The frame measures about 4.4 by 1.5 m, standing roughly 0.5 m high. A part like this is tack welded on a fixture and welded out, with the bores and pads machined after welding.
- Length, width and height
- 4 365 x 1 480 x 462 mm
- 4 365 x 1 480 x 462 mm. Longest dimension 4 365 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Support frame with mounting brackets, 4.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A support frame of this kind is built from welded box and channel sections forming a long ladder shaped base, with plated gusset brackets, bored lugs, lifting eyes and a raised plated cradle at one end. Standout features include rows of stiffening ribs, bolted mounting brackets with machined bores, and a boxed rear crossmember. It measures about 4.1 m long, 2.2 m wide and 1.5 m high. Such a part is set on a fixture, tacked and welded out, then bored and faced on the boring mill.
- Length, width and height
- 4 140 x 2 242 x 1 530 mm
- 4 140 x 2 242 x 1 530 mm. Longest dimension 4 140 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Frame with hook brackets, 4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded box section frame forms a long rectangular ladder base with cross members. Plated corner brackets sit at each end, and rows of hook shaped lugs and small stiffener ribs stand up along both long sides, with bored pin holes through several brackets. The hook fronts and angled end brackets stand out most. It measures about 4.0 by 2.2 m, and 1.2 m high. Parts like this are set on a fixture, tacked and welded out, with every bore and pad cut after welding.
- Length, width and height
- 4 000 x 2 181 x 1 158 mm
- 4 000 x 2 181 x 1 158 mm. Longest dimension 4 000 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Ladder frame with side brackets, 3.8 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A ladder frame with side brackets forms two long rails joined by several cross tubes, with folded end plates, hanging lugs and rows of hook ended brackets running along both sides. The crossed centre brace and the hook fronted end beams stand out against the open rail bays. It measures about 3.8 m long, 2.2 m wide and 0.5 m high. Pieces like this are set on a fixture, tacked and welded out, with every bore and pad cut after welding.
- Length, width and height
- 3 770 x 2 159 x 506 mm
- 3 770 x 2 159 x 506 mm. Longest dimension 3 770 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Chassis frame with cross member, 3.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded chassis frame built from plated side walls, box section rails and a tall upright tower of ribbed plates at one end, tied across by a box cross member. A curved top edge sweeps over the tower, with bored holes, slotted lugs and machined pads set along the rails and side plates. It measures about 3.7 m long, 2.3 m wide and 2.0 m high. A part like this is welded out on a fixture, with the bores and pads machined after welding.
- Length, width and height
- 3 669 x 2 300 x 1 977 mm
- 3 669 x 2 300 x 1 977 mm. Longest dimension 3 669 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Machined side frame, 3.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machined side frame runs as a long slim weldment of plate and channel, with cross members, paired upright brackets along its length and a folded mounting plate at one end. The standout feature is a large bored ring opening at the other end, with a machined face around it and drilled lugs nearby. It measures about 3.5 m long, 0.9 m wide and 0.5 m high. Such parts are tack welded on a fixture and welded out, then machined after welding on a horizontal boring mill.
- Length, width and height
- 3 534 x 896 x 541 mm
- 3 534 x 896 x 541 mm. Longest dimension 3 534 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Braced truss frame, 3.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A braced truss frame made of two long folded side panels tilted on an incline, held apart by cross tubes and diagonal bracing, with pivot lugs and mounting brackets at both ends. The folded top edge of each panel and the crossed bracing underneath stand out, keeping the whole frame square and rigid. It measures about 3.2 m long, 2.6 m wide and 1.4 m high. Parts like this are folded on the press brake and welded out on a fixture.
- Length, width and height
- 3 155 x 2 573 x 1 425 mm
- 3 155 x 2 573 x 1 425 mm. Longest dimension 3 155 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Side frame pair with tie bars, 3.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A side frame pair like this carries two tall plate uprights joined across by three long tie bars. Each plate has a stepped, notched outline with large and small bores, mounting pads and brackets along its edges, matched on both sides. The stepped profile and dense bore pattern stand out, giving mounting points at several heights. It measures about 3.1 by 2.1 by 2.2 m. Here a part like this is cut from plate on the laser bed and tack welded on a fixture and welded out.
- Length, width and height
- 3 130 x 2 125 x 2 200 mm
- 3 130 x 2 125 x 2 200 mm. Longest dimension 3 130 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Machine frame with box beams, 3.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machine base frame built from two deep box beams with flat machined top plates, joined by two slimmer cross beams, with slotted floor plates fitted between them. Open box ends show internal ribs, and small brackets and pads sit on the inner faces for mounting other parts. It measures about 3.1 by 3.0 m and stands about 0.7 m high. A part like this is set on a fixture, tacked and welded out, then machined after welding on a horizontal boring mill.
- Length, width and height
- 3 059 x 2 976 x 739 mm
- 3 059 x 2 976 x 739 mm. Longest dimension 3 059 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Machine base frame with plate walls, 2.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machine base frame built from two tall plate walls joined by cross beams and internal ribs. Both walls carry rectangular and circular cut-outs for access and weight saving, with round bores along the top edge for shafts or pins. It measures about 2.9 m long, 1.9 m wide and 1.8 m high. Parts like this are laser cut up to 20 mm, set on a fixture, tacked and welded out, with every bore and pad cut after welding.
- Length, width and height
- 2 942 x 1 860 x 1 764 mm
- 2 942 x 1 860 x 1 764 mm. Longest dimension 2 942 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Kinked frame with upright posts, 2.8 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A kinked frame like this starts as a rectangular base of channel and box rail, braced across with tubes, then rises into two upright posts tied by a cross member before kinking upward into a long boxed arm carrying welded hook brackets and lugs along its length. The row of mounting brackets on the raised arm stands out most. It measures about 2.8 m long, 1.6 m wide and 1.0 m high. A piece like this is set on a fixture, tacked and welded out.
- Length, width and height
- 2 819 x 1 603 x 986 mm
- 2 819 x 1 603 x 986 mm. Longest dimension 2 819 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Rotating gantry frame, 2.8 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A rotating gantry frame built from rectangular hollow section, forming an open portal with raked legs, diagonal corner braces and a top rail carrying small mounting lugs. A foot rail joins the base, with pivot brackets at each lower corner where a bored seat lines up each side for rotation. It measures about 2.8 m long, 0.8 m wide and 2.1 m high. Such a part is run on the 14 m robotic welding track when the batch allows, with the bores and pads machined after welding.
- Length, width and height
- 2 783 x 762 x 2 095 mm
- 2 783 x 762 x 2 095 mm. Longest dimension 2 783 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Welded chassis housing, 2.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded chassis housing with a stepped top deck plate with round cut-outs and studs, slotted side walls, internal ribs and a floor plate with a mounting lug. One end opens into a large pocket, the other carries a folded nose panel. The bored, studded deck stands out. It measures about 2.7 by 1.6 by 1.4 m. In this hall a part like this is cut from plate on the laser bed and tacked up on a fixture and welded through.
- Length, width and height
- 2 656 x 1 577 x 1 380 mm
- 2 656 x 1 577 x 1 380 mm. Longest dimension 2 656 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Base frame with housing box, 2.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A base frame of welded box section plate forms a flat open grid, with a plated housing box rising at one end. The housing has a sloped, open-top front wall with a machined access pocket, while the frame edges carry mounting bores and bracket cutouts along the sides. It measures about 2.4 m long, 1.5 m wide and 0.9 m high. Here a part like this is welded out on a fixture, then machined after welding on a horizontal boring mill.
- Length, width and height
- 2 422 x 1 500 x 881 mm
- 2 422 x 1 500 x 881 mm. Longest dimension 2 422 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Welded standing wall, 2.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded standing wall built from one heavy steel plate on two slim support legs. The face carries a large machined bearing bore with a bolt circle, a small round boss, cut-out windows and short tabs, with curved stiffener ribs and a lifting eye at one corner. Overall size is about 2.4 m long, 0.2 m wide and 2.4 m high. A piece like this is laser cut from plate up to 20 mm and tack welded on a fixture and welded out.
- Length, width and height
- 2 410 x 206 x 2 364 mm
- 2 410 x 206 x 2 364 mm. Longest dimension 2 410 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Machine base with ring mount, 2.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machine base frame built from two long plated box arms, joined at the back by an arched ring mount with a bored seat, plus access hatches, mounting pads and a slim bent hoop frame rising behind it. The bored ring mount, flanked by lifting lugs and stiffening ribs, is the standout feature. It measures about 2.4 m long, 2.2 m wide and 1.4 m high. A part like this is welded out on a fixture, with the bores and pads machined after welding.
- Length, width and height
- 2 385 x 2 219 x 1 374 mm
- 2 385 x 2 219 x 1 374 mm. Longest dimension 2 385 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Rear chassis weldment, 2.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A rear chassis weldment built from folded plate panels, box-section uprights and a tall curved guard hoop braced by diagonal stays. The faceted plated floor carries mounting eyes and lugs on the side plates, with small bores and a bracket set into the lower corner, plus a machined pad beneath the hoop base. It measures about 2.3 m long, 1.6 m wide and 2.3 m high. In this hall a part like this is tacked up on a fixture and welded through, with every bore and pad cut after welding.
- Length, width and height
- 2 319 x 1 606 x 2 294 mm
- 2 319 x 1 606 x 2 294 mm. Longest dimension 2 319 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Welded chassis, 2.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded chassis tub formed from folded steel plate, with deep side walls, cross walls, bored mounting pads and lugs, and a slotted vent panel in one corner. A twin-eared bracket with bored holes rises at the centre, flanked by ribs, with a small step tread at the back. It measures about 2.3 by 2.0 m, 0.6 m high. Pieces like this are tacked up on a fixture and welded through, laser cut up to 20 mm and folded over 6 050 mm on the press brake.
- Length, width and height
- 2 310 x 1 990 x 630 mm
- 2 310 x 1 990 x 630 mm. Longest dimension 2 310 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Two-level machine frame, 2.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A two-level machine frame built up from hollow section beams and legs, with small deck plates, cross members and a lower grid tying the base together. A raised rail with bored mounting holes runs along the back edge, and deck plates sit at different heights across both levels. It measures about 2.3 by 2.0 m and stands about 1.0 m high. Here a part like this is tacked up on a fixture and welded through, then bored and faced on the boring mill.
- Length, width and height
- 2 300 x 1 960 x 1 032 mm
- 2 300 x 1 960 x 1 032 mm. Longest dimension 2 300 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Machine stand base, 2.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machine stand base built as a plated weldment, with a tall centre wall, side boxes and sloped end brackets tying everything together. Both views show two drilled rail faces running along the sides, round bored holes through the wall, and flanged feet at the corners. The perforated rails and angled gusset brackets stand out most. It measures about 2.2 by 1.4 m and stands 1.0 m high. A part like this is tack welded on a fixture and welded out, with every bore and pad cut after welding.
- Length, width and height
- 2 246 x 1 367 x 1 039 mm
- 2 246 x 1 367 x 1 039 mm. Longest dimension 2 246 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Braced frame with side panels, 2.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A braced frame with side panels forms two sloping plate panels with folded top edges, set on a tube base with diagonal cross braces, gussets, pivot lugs and mounting brackets at the corners. The triangulated struts under each panel give an open trestle form, with bored lugs at both ends for pivot pins. It measures about 2.2 m long, 1.9 m wide and 0.8 m high. Here a part like this is set on a fixture, tacked and welded out, then machined after welding on a horizontal boring mill.
- Length, width and height
- 2 244 x 1 850 x 824 mm
- 2 244 x 1 850 x 824 mm. Longest dimension 2 244 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Base frame with two upright arms, 2.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A base frame of rectangular tube rails and cross braces forms a flat, open base with gusseted corners and a row of mounting bores along the rails. Two cranked, bored plate arms rise from one end, each with a small lug bracket, and a pair of short twin lugs sits at the other end. The stepped, bored arms stand out. It measures about 2.1 by 1.6 m, roughly 1.0 m high. Such parts are tack welded on a fixture and welded out.
- Length, width and height
- 2 136 x 1 639 x 1 033 mm
- 2 136 x 1 639 x 1 033 mm. Longest dimension 2 136 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Centre frame with pivot brackets, 2.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A centre frame of two long box rails ending in ring lugs, braced by cross tubes into an open ladder grid. Plated pivot brackets with bored and slotted holes hang below one corner, next to a smaller folded bracket, while mounting holes run along both rails. It measures about 2.1 m long, 1.8 m wide and 0.4 m high. A part like this is set on a fixture, tacked and welded out, with every bore and pad cut after welding.
- Length, width and height
- 2 119 x 1 808 x 357 mm
- 2 119 x 1 808 x 357 mm. Longest dimension 2 119 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Cage frame unit, 2.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A cage frame unit built up from square hollow section uprights, cross members and a slim top rail set on raised stand-offs running the full length. One tier steps down into an open diagonal brace that closes the lower corner, and a bolted bracket plate sits into one of the uprights. The welded frame measures about 2.1 m long, 0.3 m wide and 1.3 m high. In this hall a part like this is welded out on a fixture, with every bore and pad cut after welding.
- Length, width and height
- 2 100 x 340 x 1 267 mm
- 2 100 x 340 x 1 267 mm. Longest dimension 2 100 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Support frame with deck plate, 2.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A support frame built from two box rails with open ends, carrying a folded deck plate with chamfered corners above and slotted bracket plates below. Machined bores, lugs and a stub shaft sit at the front, with cross plates and gussets tying the rails together. The folded deck stands out against the boxy rails. It measures about 2.1 by 1.3 m, 0.7 m high. Such parts are welded out on a fixture, with the bores and pads machined after welding.
- Length, width and height
- 2 085 x 1 250 x 690 mm
- 2 085 x 1 250 x 690 mm. Longest dimension 2 085 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Cage frame of three nested boxes, 2.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A cage frame built from square hollow section posts and rails, three open box frames nested together, the middle box taller and set forward of the two flanking ones. Top and bottom rails carry cross slats, corner posts stay open for access, and small brackets sit on one upright near the centre post. It measures about 2.1 m long, 1.1 m wide and 0.7 m high. Pieces like this are tack welded on a fixture and welded out, then blasted and painted in the booths on site.
- Length, width and height
- 2 067 x 1 110 x 740 mm
- 2 067 x 1 110 x 740 mm. Longest dimension 2 067 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Machine stand with side plates, 2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machine stand formed from two tall side plates with chamfered, sloped shoulders, linked by a rectangular top frame and lower cross beams on flat foot plates. The side plates carry bored holes, cut-outs and small mounting brackets, with a braced lower section tying the legs together. It measures about 2.0 by 1.9 m and stands about 1.5 m high. A part like this is cut from plate on the laser bed and welded out on a fixture.
- Length, width and height
- 1 970 x 1 950 x 1 510 mm
- 1 970 x 1 950 x 1 510 mm. Longest dimension 1 970 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Handling frame, 2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A tall welded handling frame built from folded steel plate, with large cut-out window openings on two faces and a perforated grid panel across the top. One upright edge carries a row of small round holes, and the lower panel on the back face has a recessed rectangular cutout. It stands about 1.2 by 1.2 m in plan and 2.0 m high. Such a part is bent on the 400 t press brake and welded on the 14 m robotic track for a series, by hand for a one-off.
- Length, width and height
- 1 245 x 1 187 x 1 965 mm
- 1 245 x 1 187 x 1 965 mm. Longest dimension 1 965 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Upper carriage frame, 1.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
An upper carriage frame built around a rounded drilled floor plate, with two tall webs running lengthwise, cross plates, mounting pads and gusseted brackets tying the structure together. A machined pivot boss with a bored seat sits at the front, flanked by further bored holes and stiffening ribs linking the webs to the deck. It measures about 1.9 m long, 1.6 m wide and 0.4 m high. A piece like this is tack welded on a fixture and welded out, then machined after welding on a horizontal boring mill.
- Length, width and height
- 1 920 x 1 614 x 357 mm
- 1 920 x 1 614 x 357 mm. Longest dimension 1 920 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Compact frame with lugs, 1.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A compact base frame built from welded plate and box ribs, with a drilled end plate, two drilled top rails and angled stiffener webs running between them. Thick ring lugs sit at the corners, with bored pivot seats and machined pads on the top faces for mounting. It measures about 1.9 m long, 1.0 m wide and 0.6 m high. In this hall a part like this is tack welded on a fixture and welded out, with every bore and pad cut after welding.
- Length, width and height
- 1 882 x 989 x 625 mm
- 1 882 x 989 x 625 mm. Longest dimension 1 882 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Heavy front frame with bearing mounts, 1.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A heavy front frame of this kind combines a ribbed box base with angled gussets and bolting lugs at the corners, carrying two tall cheek plates pierced with pin bores and stiffened by curved ribs. A bored circular seat sits on the rear face, with lifting lugs and small mounting flanges nearby for pins and brackets. It measures about 1.9 m long, 1.3 m wide and 1.3 m high. Such parts are welded out on a fixture, then machined after welding on a horizontal boring mill.
- Length, width and height
- 1 855 x 1 250 x 1 284 mm
- 1 855 x 1 250 x 1 284 mm. Longest dimension 1 855 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Frame with curved arms, 1.8 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded frame built from rectangular tube rails and crossmembers, with a pair of curved tube arms rising from one end, braced by diagonal struts and gusset plates. Drilled lugs, clevis eyes and a flat mounting pad sit along the rails and arm tips, giving it a hook-like profile from both sides. It measures about 1.8 m long, 1.7 m wide and 0.9 m high. A piece like this is welded out on a fixture, with the bores and pads machined after welding.
- Length, width and height
- 1 809 x 1 701 x 931 mm
- 1 809 x 1 701 x 931 mm. Longest dimension 1 809 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Open cube frame, 1.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
An open cube frame made from square hollow section posts and rails, with four parallel tube rails spanning the top and a lower ring of rails near the floor. Each corner post carries a bored, bolted plate for joining to adjoining frames, and short brackets sit partway up two posts. It measures about 1.7 by 1.6 m and stands 0.9 m high. A piece like this is tack welded on a fixture and welded out, then machined after welding on a horizontal boring mill.
- Length, width and height
- 1 740 x 1 620 x 937 mm
- 1 740 x 1 620 x 937 mm. Longest dimension 1 740 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Welded chassis, left-hand

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded chassis frame of folded plate rails, cross members and gusseted ribs, with pivot lugs, a bored eye at each end and smaller bracket plates along the deck. A curved wheel arch cutout, machined pivot bores and rows of bolt holes across the deck stand out. It measures about 1.7 by 1.0 m and stands about 0.3 m high. A piece like this is tack welded on a fixture and welded out, cut from plate on the laser bed and bent on the 400 t press brake.
- Length, width and height
- 1 656 x 982 x 289 mm
- 1 656 x 982 x 289 mm. Longest dimension 1 656 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Welded chassis, 1.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded chassis frame of folded plate side rails and cross members, with a large central opening, bored lugs, mounting pads and small brackets along both sides. The ring of bores and bushings in the base plate and the twin lifting eyes at the front stand out. It measures about 1.7 by 1.3 m and stands 0.3 m high. Such parts are welded out on a fixture, with every bore and pad cut after welding.
- Length, width and height
- 1 655 x 1 286 x 338 mm
- 1 655 x 1 286 x 338 mm. Longest dimension 1 655 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Undercarriage centre frame with slew ring seat, 1.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
An undercarriage centre frame built around a flat plated deck with a machined, bolted ring seat at its core. Tapered box section legs are stiffened with ribs and gussets, with clevis lugs and bored pivot holes at the front and mounting holes around the sides. The bored ring seat is the clear focal point. It measures about 1.6 by 1.5 m and stands 0.3 m high. A piece like this is set on a fixture, tacked and welded out, with the bores and pads machined after welding.
- Length, width and height
- 1 573 x 1 541 x 318 mm
- 1 573 x 1 541 x 318 mm. Longest dimension 1 573 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Welded chassis, machined state

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A low welded chassis frame of this kind combines folded plate, box section rails, ribs, gussets and mounting brackets into a compact undercarriage. Bored lugs sit at the corners for pivot or axle seats, while flat machined pads and bored faces run along the rails for bearings and mounts, with cut-outs and tabs for fittings throughout. It measures about 1.5 m long, 1.0 m wide and 0.3 m high. A piece like this is welded out on a fixture, with every bore and pad cut after welding.
- Length, width and height
- 1 513 x 982 x 279 mm
- 1 513 x 982 x 279 mm. Longest dimension 1 513 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Machine frames and weldments
Front chassis weldment, 1.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A front chassis weldment made from folded plate walls around a wide oval opening, with a tubular end frame and rows of bolted holes along the top edges. One end carries a raised bracket with a bored bearing seat, the other fans into layered mounting plates with multiple bores. It measures about 1.5 m long, 1.1 m wide and 0.4 m high. Such parts are welded out on a fixture, laser cut up to 20 mm and bent on the 400 t press brake.
- Length, width and height
- 1 513 x 1 120 x 440 mm
- 1 513 x 1 120 x 440 mm. Longest dimension 1 513 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Welded plant structure, 8.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A mobile plant structure built as a welded chassis of channel and box section rails, carrying a raised screen box, a discharge chute and an axle with a single wheel, braced by diagonal struts and angled support legs. A sloped folded chute plate, a cylindrical drive housing and open mesh decking stand out against the plain plate rails. It measures about 8.2 m long, 2.4 m wide and 3.0 m high. Such parts are tacked up on a fixture and welded through.
- Length, width and height
- 8 219 x 2 350 x 3 016 mm
- 8 219 x 2 350 x 3 016 mm. Longest dimension 8 219 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Mobile plant structure, complete, 12 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A mobile plant structure made up of a plated chassis on skid feet, a boxed feed hopper, a screen box on spring mounts, and a folded stacking conveyor with lattice side rails. Support legs, a fold-up discharge lip and chain bracing on the conveyor boom stand out. It measures about 12.0 m long, 2.9 m wide and 3.6 m high. In this hall a part like this is set on a fixture, tacked and welded out and laser cut from plate up to 20 mm.
- Length, width and height
- 11 993 x 2 898 x 3 616 mm
- 11 993 x 2 898 x 3 616 mm. Longest dimension 11 993 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Belt conveyor frame with drive, 11.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A belt conveyor frame with plated side walls, cross bracing and idler brackets along the trough, a drive drum housing and support legs at one end. It has a folded edge rail, evenly spaced stiffeners, an inspection hatch and sloped legs under the drive. It measures about 11.2 m long, 1.6 m wide and 1.5 m high. Parts like this are tacked up on a fixture and welded through, laser cut up to 20 mm and folded over 6 050 mm on the press brake.
- Length, width and height
- 11 183 x 1 620 x 1 539 mm
- 11 183 x 1 620 x 1 539 mm. Longest dimension 11 183 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Welded plant structure, 14.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A mobile plant structure built around a central screen box on a welded chassis of box and hollow section, with an inclined conveyor frame lifting from each end on truss legs, a wheeled axle, folding support legs and small lifting lugs. What stands out is the pair of long raking conveyor gantries with cross bracing rising from the low central frame. It measures about 14.6 m long, 8.4 m wide and 3.9 m high. A part like this is welded out on a fixture.
- Length, width and height
- 14 645 x 8 423 x 3 858 mm
- 14 645 x 8 423 x 3 858 mm. Longest dimension 14 645 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Folding belt conveyor frame, 10.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A folding belt conveyor frame, built as a long plated trough with ribbed side skirts, a drive drum housing at one end and a slim hinged arm that folds the tail section out. A square inspection hatch sits mid-trough, with the folding joint and pivot standing out clearly. It measures about 10.1 m long, 2.6 m wide and 1.4 m high. Such a part is tacked up on a fixture and welded through and laser cut from plate up to 20 mm.
- Length, width and height
- 10 094 x 2 571 x 1 389 mm
- 10 094 x 2 571 x 1 389 mm. Longest dimension 10 094 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Kinked conveyor frame with drive, 8.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
Kinked belt conveyor frame with a drive unit at the top end. It is made up of long side plates, a trough deck, cross members, a hollow-section frame at the low end and lugs along the sides. The bend between the level run and the incline stands out. It measures about 8.9 by 1.7 m. Here a part like this is tack welded on a fixture and welded out.
- Length, width and height
- 8 913 x 1 705 x 3 153 mm
- 8 913 x 1 705 x 3 153 mm. Longest dimension 8 913 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Hopper container with three inclined conveyors, 13.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A hopper container structure stands on a closed box container base, with corrugated side plate, three internal hopper bins, and a grid of support posts and cross bracing along the side. Three parallel inclined conveyor troughs climbing in unison from the hopper outlets stand out. It measures about 13.5 m long, 12.2 m wide and 8.5 m high. A piece like this is tacked up on a fixture and welded through and welded on the robotic track or by hand.
- Length, width and height
- 13 482 x 12 196 x 8 468 mm
- 13 482 x 12 196 x 8 468 mm. Longest dimension 13 482 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Welded conveyor assembly, 5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded conveyor support frame rises on four perforated, lattice-style legs, tied together by a long cross beam with plate ribs, pivot brackets and lifting eyes on top. One end boxes up into a machined housing with a bored pivot seat, while the legs carry rows of lightening holes for a lighter, open structure. It measures about 4.9 m long, 2.4 m wide and 2.0 m high. A piece like this is set on a fixture, tacked and welded out and laser cut from plate up to 20 mm.
- Length, width and height
- 4 940 x 2 431 x 2 023 mm
- 4 940 x 2 431 x 2 023 mm. Longest dimension 4 940 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Side discharge conveyor, 4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
An inclined side discharge conveyor with ladder-style channel side rails cross-braced with rungs, a cylindrical head drum housing at the top and a slim idler drum at the foot. A braced diagonal arm props the frame, with lugs and a chain for angle adjustment. It measures about 3.9 m long, 0.8 m wide and 1.8 m high. Such a part is welded by hand or on the 14 m robotic welding track, then bored and faced on the boring mill.
- Length, width and height
- 3 949 x 776 x 1 793 mm
- 3 949 x 776 x 1 793 mm. Longest dimension 3 949 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Tracked mobile plant structure, complete, 12.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A tracked mobile plant structure built from a deep flared hopper, a louvred machine house with access panels, a folded crawler undercarriage and a long inclined conveyor on a braced truss frame. Handrails, lifting lugs and stiffening ribs run along the hopper edges and conveyor sides. It measures about 12.4 m long, 2.6 m wide and 3.4 m high. Here a part like this is set on a fixture, tacked and welded out and welded on the 14 m robotic track for a series, by hand for a one-off.
- Length, width and height
- 12 359 x 2 579 x 3 383 mm
- 12 359 x 2 579 x 3 383 mm. Longest dimension 12 359 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Discharge conveyor frame, 10.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A long discharge conveyor frame, built as a welded truss from twin top and bottom chords, zigzag diagonals and cross braces, with idler brackets stepped along both top edges and end plates with mounting bores at each end. A folded walkway edge runs along one side, with small gusseted lugs for guards and sensors. It measures about 10.2 m long, 1.1 m wide and 1.7 m high. Such parts are welded on the robotic track or by hand, with the bores and pads machined after welding.
- Length, width and height
- 10 213 x 1 053 x 1 694 mm
- 10 213 x 1 053 x 1 694 mm. Longest dimension 10 213 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Conveyor frame, 8.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A conveyor frame built as a ladder of two long rails joined by regular cross members, with plate gussets, bolt holes and small brackets at the lower end. The rails curve smoothly up to a raised, boxed centre section with closer stiffeners, then taper to a narrow end with lugs for pivots or rollers. It measures about 8.6 m long, 1.6 m wide and 2.7 m high. Pieces like this are welded on the robotic track or by hand, then machined after welding on a horizontal boring mill.
- Length, width and height
- 8 559 x 1 550 x 2 749 mm
- 8 559 x 1 550 x 2 749 mm. Longest dimension 8 559 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Conveyor frame with feed chute, 6.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A conveyor frame runs the length of two slim side rails joined by regular cross members, ending in a plated feed chute with raised, angled side walls. The flared chute mouth, the folded plate walkway edges and the pivot brackets at the far end stand out. It measures about 6.6 m long, 1.0 m wide and 1.2 m high. In this hall a part like this is run on the 14 m robotic welding track when the batch allows, with the bores and pads machined after welding.
- Length, width and height
- 6 554 x 989 x 1 159 mm
- 6 554 x 989 x 1 159 mm. Longest dimension 6 554 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Conveyor frame with cover deck, 4.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A conveyor frame built from two long side rails with drilled webs, cross members and gussets, carrying a drilled cover deck of plate over part of the top and a plated chute hanging below one end. The chute's angled front plate and the rows of bolt holes along the rails and deck stand out. It measures about 4.9 m long, 1.5 m wide and 0.6 m high. In this hall a part like this is tack welded on a fixture and welded out, then blasted and painted in house.
- Length, width and height
- 4 943 x 1 480 x 602 mm
- 4 943 x 1 480 x 602 mm. Longest dimension 4 943 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Plant structure, main assembly, 4.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A screen box forms the main assembly of this plant structure, with deep plated side walls, folded stiffening ribs, a drive housing on one face and a sloped discharge lip at the open end. Angled brackets and a mesh deck sit inside the folded shell, with lifting lugs along the top edge. It measures about 4.1 by 2.5 m and stands 1.4 m high. Such a part is tacked up on a fixture and welded through, with the bores and pads machined after welding.
- Length, width and height
- 4 078 x 2 466 x 1 443 mm
- 4 078 x 2 466 x 1 443 mm. Longest dimension 4 078 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Plant structure, sub-assembly, 3.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A plant sub-assembly built from two sloped deck plates meeting at a folded central ridge, carried on angled side plates. The side plates carry a row of bored holes along their length, with brackets and clevis lugs at both ends for pinning into a larger frame. It measures about 3.3 m long, 1.6 m wide and 0.6 m high. Pieces like this are tacked up on a fixture and welded through, laser cut up to 20 mm and folded on the press brake.
- Length, width and height
- 3 307 x 1 646 x 610 mm
- 3 307 x 1 646 x 610 mm. Longest dimension 3 307 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Screen deck frame with discharge lip, 3.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A screen deck frame of folded side plates with rows of bolt holes, cross braces, and small mounting lugs along the edges. One end folds down into an angled, ribbed discharge lip with a bolted edge, stiffened underneath by boxed gussets seen from the back. It measures about 3.3 m long, 1.6 m wide and 0.6 m high. Pieces like this are set on a fixture, tacked and welded out, laser cut from plate up to 20 mm and bent on the 400 t press brake.
- Length, width and height
- 3 303 x 1 569 x 648 mm
- 3 303 x 1 569 x 648 mm. Longest dimension 3 303 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Roller frame with upright posts, 3.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A roller frame built up from a rectangular box section base that kinks upward into a long sloped arm, with cross tubes, diagonal struts and internal bracing tying the frame together. Two upright posts rise from the base, and hook brackets and mounting lugs line both sides and the arm edge. It measures about 3.3 by 1.5 m, standing 1.1 m high. Such parts are tack welded on a fixture and welded out.
- Length, width and height
- 3 283 x 1 514 x 1 070 mm
- 3 283 x 1 514 x 1 070 mm. Longest dimension 3 283 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Side conveyor frame, 2.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A side conveyor frame made from two profiled side plates joined by cross tubes and diagonal braces, with slotted lightening holes, a folded lower pan and a mounting bore through one plate. Each end splits into a pair of fork arms, with lifting lugs welded on top. It measures about 2.3 m long, 1.7 m wide and 0.7 m high. A part like this is laser cut from plate up to 20 mm and tacked up on a fixture and welded through.
- Length, width and height
- 2 293 x 1 656 x 694 mm
- 2 293 x 1 656 x 694 mm. Longest dimension 2 293 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Conveyor frame, 2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A conveyor frame of this kind is built from two tall side plates with rows of square windows, tied together by cross members and a folded top flange along each edge. Bored pivot eyes sit at both corners of one end, with a central bored lug on the opposite side. It measures about 2.0 by 1.6 m and stands about 0.6 m high. A part like this is cut from plate on the laser bed and tacked up on a fixture and welded through.
- Length, width and height
- 1 999 x 1 590 x 649 mm
- 1 999 x 1 590 x 649 mm. Longest dimension 1 999 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Conveyor side beam with cut-outs, 1.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A conveyor side beam made from a long side plate with a folded top flange, rectangular cut-outs along the web backed by folded triangular tabs, and drilled holes along the lower edge with a small bracket at one end. The regular rhythm of cut-outs and tabs stiffens the open web. It measures about 1.9 m long, 0.2 m wide and 0.5 m high. Pieces like this are set on a fixture, tacked and welded out and laser cut up to 20 mm.
- Length, width and height
- 1 895 x 197 x 488 mm
- 1 895 x 197 x 488 mm. Longest dimension 1 895 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Welded cross member with side brackets, 1.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded cross member joins two side brackets with box section rails, diagonal braces and a cross tube, tied together by gusset plates and reinforcing ribs. Each bracket is a folded plate arm with slotted holes, bored pin lugs and a pierced flange face for mounting. Overall size is about 1.7 m long, 1.3 m wide and 0.7 m high. A piece like this is set on a fixture, tacked and welded out, with every bore and pad cut after welding.
- Length, width and height
- 1 710 x 1 298 x 694 mm
- 1 710 x 1 298 x 694 mm. Longest dimension 1 710 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Rotor with beater bars and belt pulley, 1.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A rotor like this carries four straight beater bars welded along a shaft between two end plates, with a grooved belt pulley mounted on one bearing housing and a lifting eye at the opposite end. The spiral run of bars and the machined bearing seats on each face stand out against the plain plate body. It measures about 1.7 m long, 0.9 m wide and 0.8 m high. Here a part like this is welded out on a fixture, then bored and faced on the boring mill.
- Length, width and height
- 1 697 x 867 x 820 mm
- 1 697 x 867 x 820 mm. Longest dimension 1 697 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Conveyor frame, 1.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A conveyor frame built from two deep plate side walls joined by cross tubes and flat bracing, with eye lugs, clevis plates and a stub shaft at the corners. Square mounting bores, bolt holes and box brackets at the lower corners stand out on the plates. It measures about 1.6 by 1.5 m and 0.5 m high. Parts like this are tacked up on a fixture and welded through, with the bores and pads machined after welding.
- Length, width and height
- 1 595 x 1 492 x 477 mm
- 1 595 x 1 492 x 477 mm. Longest dimension 1 595 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Conveyor and handling structures
Welded cross member with side brackets, 1.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded cross member joins two angled plate brackets with a central box section tube and short stub arms. Each bracket is built from folded plates and gussets, with a bored pivot lug, rows of mounting holes and slotted faces for fitting other parts. It measures about 1.5 m long, 0.9 m wide and 0.5 m high. A piece like this is welded out on a fixture and laser cut from plate up to 20 mm.
- Length, width and height
- 1 458 x 937 x 498 mm
- 1 458 x 937 x 498 mm. Longest dimension 1 458 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Walkway platform with stairs and railings, 9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A long grating walkway forms the deck of this platform, built up from steel channel edge beams, tubular handrails and raking props that angle down to base plates. A wider grating landing with a ladder-like brace sits at one end, while open steel stair treads with handrails descend from the other. The structure measures about 9.0 m long, 4.0 m wide and 3.0 m high. In this hall a part like this is welded out on a fixture, then blasted and painted in the booths on site.
- Length, width and height
- 9 001 x 3 982 x 3 014 mm
- 9 001 x 3 982 x 3 014 mm. Longest dimension 9 001 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Storage rack system, 19 m run

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A storage rack system like this is built from tall box-section columns joined by cantilever arms in level rows, with raked back braces on welded base plates. A repeating run of matched frames stands alongside one spare frame. It measures about 18.9 by 5.6 m and stands about 6.0 m high. A part like this is set on a fixture, tacked and welded out and welded by hand or on the 14 m robotic welding track.
- Length, width and height
- 18 935 x 5 555 x 6 005 mm
- 18 935 x 5 555 x 6 005 mm. Longest dimension 18 935 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Raised container on posts with landing and stairs, 9.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A raised container body stands on tubular steel posts with square base plates, cross braced and topped by a corrugated grating roof. Its open end carries a railed grating landing with mesh infill and a railed stair down to the floor, while the walls show folded corrugated panels and a door opening. It measures about 9.2 m long, 6.1 m wide and 4.9 m high. Such parts are welded out on a fixture.
- Length, width and height
- 9 173 x 6 056 x 4 921 mm
- 9 173 x 6 056 x 4 921 mm. Longest dimension 9 173 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Rack bay, 6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A rack bay made from two long box section beams carried on a row of welded box section uprights, braced along the base with diagonal ties and linked at both ends by cantilever arms with drilled plates. The repeating open bays between posts and the bolt holed end arms stand out. It measures about 6.0 m long, 1.7 m wide and 1.3 m high. Such a part is welded by hand or on the 14 m robotic welding track, with every bore and pad cut after welding.
- Length, width and height
- 6 005 x 1 707 x 1 302 mm
- 6 005 x 1 707 x 1 302 mm. Longest dimension 6 005 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Stair unit with platform, 2.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A mobile stair unit built up from a grating stair, a grating platform and a raised grating shelf, framed in hollow section posts and rails with tubular handrails on both sides. A base frame of hollow sections carries castors at one end so the whole unit can be rolled into place. It measures about 1.9 by 1.2 m and stands about 2.0 m high. A part like this is welded out on a fixture, then blasted and painted before shipping.
- Length, width and height
- 1 870 x 1 240 x 2 050 mm
- 1 870 x 1 240 x 2 050 mm. Longest dimension 2 050 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Support stand row with saddles, 5.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A row of plate uprights forms this support stand, each pair cut into a deep rounded saddle and braced back to a common base rail on angled foot plates with bolt holes. The slotted, pierced tops and the clean curved seats between each pair stand out. It measures about 5.3 by 1.9 m and stands about 2.1 m high. Parts like this are cut on the 2 000 x 4 000 mm laser bed, plate up to 20 mm and welded out on a fixture.
- Length, width and height
- 5 250 x 1 884 x 2 100 mm
- 5 250 x 1 884 x 2 100 mm. Longest dimension 5 250 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Handrail and guard rail set

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A handrail and guard rail set made from bent tube hoops forms two linked frames, one open like a rail gate, the other closed with a curved solid guard panel. A diagonal tube brace stiffens one leg, and each post foot ends in a flat, bolted mounting plate. It measures about 1.1 by 0.7 m and stands 1.1 m high. Here a part like this is bent on the 400 t press brake and welded on the robotic track or by hand.
- Length, width and height
- 1 146 x 721 x 1 070 mm
- 1 146 x 721 x 1 070 mm. Longest dimension 1 146 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Storage column, 7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A storage column built as a long welded box section in plate, with a row of small brackets and bolt holes down its length and an insert strip along the top face. One end carries a large square foot plate, drilled for fixing and braced inside with a diagonal rib. Overall it measures about 7.0 by 1.5 by 1.5 m. Parts like this are welded by hand or on the 14 m robotic welding track, then bored and faced on the boring mill.
- Length, width and height
- 6 955 x 1 500 x 1 500 mm
- 6 955 x 1 500 x 1 500 mm. Longest dimension 6 955 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Ladder frame with cross rungs, 6.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A ladder frame built from two long box-section stringers joined by evenly spaced cross rungs, lying flat and open between the rails. Both ends carry bored eyes for pinning, with a round bar set across one end for a hinge or lifting point. It measures about 6.2 m long, 0.6 m wide and 0.1 m high. Parts like this are set on a fixture, tacked and welded out, with every bore and pad cut after welding.
- Length, width and height
- 6 229 x 571 x 145 mm
- 6 229 x 571 x 145 mm. Longest dimension 6 229 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Rotary store column, 6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
Rotary store column built as a long welded box section from plate, with top flanges and an end plate carrying a ring of bolt holes and a large bore. Rectangular and round cut-outs run along both side faces, with a pair of lugs near one end. It measures about 6.0 by 0.6 m. Such a part is cut on the 2 000 x 4 000 mm laser bed, plate up to 20 mm and tacked up on a fixture and welded through.
- Length, width and height
- 6 042 x 609 x 510 mm
- 6 042 x 609 x 510 mm. Longest dimension 6 042 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Rack element, 5.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A rack element built as a ladder-like frame of two parallel channel beams joined by evenly spaced upright posts, with flat plated panels running along the top edges. Both ends fold into open, flared sections with bolt holes for linking further modules. It measures about 5.8 m long, 1.6 m wide and 1.3 m high. Such a part is cut from plate on the laser bed, folded on the 400 t press brake and welded out on a fixture.
- Length, width and height
- 5 830 x 1 550 x 1 302 mm
- 5 830 x 1 550 x 1 302 mm. Longest dimension 5 830 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Guard frame of hollow sections, 4.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A guard frame built from square hollow section posts and rails, forming an open upright cage in three bays with a top rail running the full length. The middle bay steps back and carries a small shelf frame at mid height, braced with short diagonal ties. Base plates sit under each post. It measures about 4.5 m long, 0.5 m wide and 1.1 m high. Here a part like this is welded by hand or on the 14 m robotic welding track.
- Length, width and height
- 4 480 x 530 x 1 136 mm
- 4 480 x 530 x 1 136 mm. Longest dimension 4 480 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Welding fixture, panel assembly

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
Welding fixture table for a panel assembly, made up of a perimeter edge rail, eight legs with levelling feet on square foot plates, and a grid of plate and box section risers. Rows of clamp posts stand on top. It measures about 3.3 by 2.7 m. Parts like this are tacked up on a fixture and welded through.
- Length, width and height
- 3 280 x 2 700 x 1 109 mm
- 3 280 x 2 700 x 1 109 mm. Longest dimension 3 280 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Platform frame with guard rails, 3.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A flat rectangular platform frame built up from hollow section members, with cross braces forming the floor support and three open guard rail panels fixed to it, one at each end and one across the middle. Each rail panel has evenly spaced vertical posts between top and bottom rails. It measures about 3.2 by 2.2 m, standing roughly 0.4 m high. Such parts are set on a fixture, tacked and welded out.
- Length, width and height
- 3 210 x 2 210 x 434 mm
- 3 210 x 2 210 x 434 mm. Longest dimension 3 210 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Welding fixture, panel assembly, variant B

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welding fixture built as an open box-section frame, with angled braced uprights, a cross-braced base and levelling feet on mounting pads. Two steeply raked panel supports carry rows of toggle clamps on flat plate faces set at matching angles. It measures about 2.9 by 2.1 m and stands about 1.9 m high. Such parts are set on a fixture, tacked and welded out, then checked against the drawing with the measuring arm.
- Length, width and height
- 2 880 x 2 055 x 1 926 mm
- 2 880 x 2 055 x 1 926 mm. Longest dimension 2 880 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Top crossbeam, 2.75 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A top crossbeam structure like this frames a raised platform on box section legs, with plated beams, a flat chequered deck and bolted base pads at each foot. The notable feature is the open stepped corner where the deck drops away, framed by diagonal gussets and a folded plated end panel. It measures about 2.8 by 1.9 m and stands about 0.9 m high. A part like this is tacked up on a fixture and welded through, with the bores and pads machined after welding.
- Length, width and height
- 2 750 x 1 910 x 914 mm
- 2 750 x 1 910 x 914 mm. Longest dimension 2 750 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Service platform with tubular guard rail, 2.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A service platform made from a narrow folded steel plate deck set in a welded box edge, with a bent tubular guard rail of mid rails and upright posts along one side. One end curves into a hooped gate opening, with a hinge lug and bracket for the swinging section. It measures about 2.4 m long, 0.6 m wide and 1.2 m high. A part like this is folded on the 400 t press brake and run on the 14 m robotic welding track when the batch allows.
- Length, width and height
- 2 352 x 559 x 1 152 mm
- 2 352 x 559 x 1 152 mm. Longest dimension 2 352 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Tubular guard rail, 1.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A tubular guard rail made from round hollow section tube, with a bent top rail of rounded corners, a mid rail and four vertical posts. One post is cranked at the foot, stepping the rail down to a lower fixing level and giving the frame an offset end. It measures about 1.7 m long, 0.6 m wide and 1.1 m high. A part like this is run on the 14 m robotic welding track when the batch allows, then blasted and painted in house.
- Length, width and height
- 1 736 x 550 x 1 085 mm
- 1 736 x 550 x 1 085 mm. Longest dimension 1 736 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Platforms and access steel
Step with perforated treads, 1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A step unit with two perforated tread plates set side by side, each with a row of circular lightening holes, carried on an end flange with bolt lugs and ribs underneath. A perforated support box sits under one tread, with slotted edges for fixing at its base. It measures about 0.9 m long, 0.6 m wide and 0.5 m high. A part like this is laser cut up to 20 mm and set on a fixture, tacked and welded out.
- Length, width and height
- 950 x 607 x 509 mm
- 950 x 607 x 509 mm. Longest dimension 950 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Silo with support structure, platform and stairs, 10.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A rectangular plated silo body tapers into two hopper cones feeding outlets, carried on a braced column and rod frame. A railed roof platform with grating sits on top, reached by a stair tower with intermediate landings at one end. It measures about 10.9 m long, 4.3 m wide and 9.4 m high. Such a part is welded out on a fixture, then machined after welding on a horizontal boring mill.
- Length, width and height
- 10 880 x 4 270 x 9 417 mm
- 10 880 x 4 270 x 9 417 mm. Longest dimension 10 880 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Cylindrical tank in container frame, 12.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A cylindrical tank sits on saddle supports inside a container frame, with corner posts, roof bows and corrugated end and side walls around the rolled shell. The open side here shows the tank, its saddles and the box section frame, while the roof bows span across without sheeting. It measures about 12.2 m long, 2.4 m wide and 2.6 m high. Pieces like this are run on the 14 m robotic welding track when the batch allows.
- Length, width and height
- 12 214 x 2 438 x 2 591 mm
- 12 214 x 2 438 x 2 591 mm. Longest dimension 12 214 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Silo body in support frame, 4.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A square silo body tapers into a pyramid cone, set in a welded frame of hollow section legs with cross bracing on four corners. Flanged top edges carry a bolted cover plate, and a hooped ladder guard with cutouts rises from one side. It measures about 4.7 by 4.0 m and stands 4.9 m high. In this hall a part like this is tacked up on a fixture and welded through, then blasted and painted before shipping.
- Length, width and height
- 4 669 x 4 004 x 4 882 mm
- 4 669 x 4 004 x 4 882 mm. Longest dimension 4 882 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Twin hopper unit in container frame, 6.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A twin hopper unit built into a container frame, two plated hoppers side by side with sloped bottoms, discharge outlets, and folded top edges, all carried on corner castings over a floor grid of hollow sections and rows of short posts. The split top opening and paired discharge chutes with access covers stand out against the box frame. It measures about 6.1 by 2.6 by 2.6 m. Parts like this are welded on the robotic track or by hand, with every bore and pad cut after welding.
- Length, width and height
- 6 058 x 2 563 x 2 591 mm
- 6 058 x 2 563 x 2 591 mm. Longest dimension 6 058 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Feed hopper, 4.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A long open feed hopper formed from folded steel plate, with sloped end walls, folded top edges and a central longitudinal beam bracing the floor underneath. Diagonal ribs stiffen one end wall, while flanged lugs, bolt holes and mounting pads along the sides and ends allow connection to adjoining equipment. It measures about 4.9 by 2.5 m and stands 0.8 m high. Pieces like this are folded on the 400 t press brake and run on the 14 m robotic welding track when the batch allows.
- Length, width and height
- 4 888 x 2 500 x 755 mm
- 4 888 x 2 500 x 755 mm. Longest dimension 4 888 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Feed hopper with side flaps, 4.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A feed hopper in plate: a flat feed tray in a folded rim frame, plate flaps along both long sides and a rear wall with a grating step. A round drive housing hangs underneath, with brackets on the sides. It is about 4.6 m long, 2.6 m wide and 1.6 m high. Pieces like this are folded on the 400 t press brake and run on the 14 m robotic welding track when the batch allows.
- Length, width and height
- 4 566 x 2 568 x 1 595 mm
- 4 566 x 2 568 x 1 595 mm. Longest dimension 4 566 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Triple hopper unit in container frame, 12.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A triple hopper unit built from three plated, sloped hoppers set in a row inside a container frame with corner castings. Folded plate walls taper down to a narrow discharge opening under each hopper, carried on a floor grid of hollow sections with rows of short posts. It measures about 12.2 m long, 2.4 m wide and 2.6 m high. In this hall a part like this is tacked up on a fixture and welded through, then finished in the blasting and paint booths on site.
- Length, width and height
- 12 192 x 2 438 x 2 591 mm
- 12 192 x 2 438 x 2 591 mm. Longest dimension 12 192 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Trough hopper with stiffening ribs, 4.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
An open trough hopper made from folded steel plate with sloped side walls and a flat base, stiffened by upright ribs along both sides. Round bored ports sit in each wall, with a hinged inspection door and a smaller access panel near one end. It measures about 4.7 m long, 1.4 m wide and 0.8 m high. A piece like this is bent on the 400 t press brake and run on the 14 m robotic welding track when the batch allows.
- Length, width and height
- 4 664 x 1 364 x 750 mm
- 4 664 x 1 364 x 750 mm. Longest dimension 4 664 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Formed trough section, 7.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A formed trough section built from folded steel plate, with side walls curving down into a rounded base and a row of oval openings along one wall. A rolled, U-shaped lip closes one end, while a small bracket and angled lug sit underneath near the other. It measures about 7.4 m long, 1.5 m wide and 0.6 m high. Pieces like this are folded on the press brake and welded on the 14 m robotic track for a series, by hand for a one-off.
- Length, width and height
- 7 353 x 1 480 x 554 mm
- 7 353 x 1 480 x 554 mm. Longest dimension 7 353 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Screw conveyor tube with flanged branches, 6.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A screw conveyor tube with flanged branches: a long round shell with a bolted flange at each end, plus a square inlet branch and a round outlet branch angled off the main tube. Machined flange faces with bolt hole rings stand out, along with a small stub on one end plate. It measures about 6.4 m long, 1.5 m wide and 1.4 m high. Such parts are welded on the 14 m robotic track for a series, by hand for a one-off.
- Length, width and height
- 6 427 x 1 480 x 1 377 mm
- 6 427 x 1 480 x 1 377 mm. Longest dimension 6 427 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Small hopper assembly, 4.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A small hopper assembly built from a square top-fed box with folded plate walls, tapering to a pyramidal chute with an outlet valve, carried on four tube legs with cross braced lattice bracing and welded foot plates. The crossed diagonal bracing and flanged top rim stand out. It measures about 1.8 by 1.6 m in plan and stands about 4.9 m high. A part like this is tack welded on a fixture and welded out.
- Length, width and height
- 1 750 x 1 550 x 4 865 mm
- 1 750 x 1 550 x 4 865 mm. Longest dimension 4 865 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Hopper side wall, left, 4.8 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A long sloped hopper side plate with a folded top lip and angled end flanges that kick outward at both ends. A row of slotted cutouts runs along the top edge, and one end carries a small stiffened bracket for fixing to the neighbouring frame. It measures about 4.8 m long, 0.5 m wide and 0.7 m high. Such parts are set on a fixture, tacked and welded out and cut from plate on the laser bed.
- Length, width and height
- 4 768 x 477 x 730 mm
- 4 768 x 477 x 730 mm. Longest dimension 4 768 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Hopper wall plate, 4.8 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A hopper wall plate made from a long folded steel panel with a narrow top flange, an angled fin at one end and a stepped tab at the other, with square and slotted cut-outs along its length for fittings and access. The matched square openings and the sharply angled end stand out. It measures about 4.8 m long, 0.3 m wide and 0.7 m high. A part like this is set on a fixture, tacked and welded out and laser cut up to 20 mm.
- Length, width and height
- 4 768 x 325 x 730 mm
- 4 768 x 325 x 730 mm. Longest dimension 4 768 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Welded pontoon hull, 4.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded pontoon hull is an open plate tub with a raked bow, folded rubbing strakes along both sides, a centre bulkhead, corner lifting eyes and a bollard on the stern deck. The raked bow and the folded strake lines stand out against the plain plate sides. It measures about 4.2 by 1.5 m and stands about 1.0 m high. A part like this is set on a fixture, tacked and welded out, laser cut from plate up to 20 mm and folded on the press brake.
- Length, width and height
- 4 198 x 1 547 x 1 036 mm
- 4 198 x 1 547 x 1 036 mm. Longest dimension 4 198 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Welded flap assembly, 3.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded flap assembly built as a long plated box frame with cut-out windows, ribbed underside and a row of stiffeners, carried on two shaped pivot arms with hinge brackets below. Each arm ends in a machined bore with a protruding pin, set to take a mating shaft. It measures about 3.3 m long, 0.6 m wide and 1.5 m high. Pieces like this are cut from plate on the laser bed and welded out on a fixture.
- Length, width and height
- 3 282 x 644 x 1 540 mm
- 3 282 x 644 x 1 540 mm. Longest dimension 3 282 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Bunker hopper body, 1.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A bunker hopper body formed from two angled plate walls meeting in an L shape, with folded upper edges, upright stiffening ribs, a floor plate and hinge lugs at the side. A pivot bore and bracket plates under the trough stand out, along with the folded wall edges and rib pattern. It measures about 1.9 by 1.9 m and 1.0 m high. In this hall a part like this is welded out on a fixture, then machined after welding on a horizontal boring mill.
- Length, width and height
- 1 935 x 1 924 x 1 017 mm
- 1 935 x 1 924 x 1 017 mm. Longest dimension 1 935 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Feed hopper section with stiffened walls, 1.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A feed hopper section built as a tapered plate box with sloped side walls, folded top and bottom edges, and external stiffener ribs along the faces. Mounting brackets, lifting hooks and small bored pads sit along the sides, while the open throat reveals internal corrugated baffle plates set in angled rows. It measures about 1.5 by 1.4 m and stands about 1.6 m high. Such a part is welded out on a fixture, then blasted and painted before shipping.
- Length, width and height
- 1 503 x 1 406 x 1 609 mm
- 1 503 x 1 406 x 1 609 mm. Longest dimension 1 609 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Deck section with built-in tank, 1.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A deck section built around a rectangular tank welded beneath a drilled flat plate, with a sloped, notched end wall and profiled side edges. Round flanged ports sit in the tank face, with a stub outlet and bolt holes across the deck. The sloped end plate and flanged bores stand out. It measures about 1.5 by 0.8 m, 0.5 m high. Here a part like this is tack welded on a fixture and welded out, laser cut up to 20 mm and folded on the press brake.
- Length, width and height
- 1 540 x 818 x 508 mm
- 1 540 x 818 x 508 mm. Longest dimension 1 540 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Tanks, hoppers and silos
Slide gate frame with hand crank, 1.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A slide gate frame built from welded box section rails forming a flat square frame, with a steel sliding plate running in guide channels and mounting lugs at the corners. A threaded spindle crosses the frame to a hand crank on one side, driving the plate between its rails. It measures about 1.4 by 1.2 m and stands about 0.2 m high. Parts like this are tacked up on a fixture and welded through, then machined after welding on a horizontal boring mill.
- Length, width and height
- 1 436 x 1 220 x 194 mm
- 1 436 x 1 220 x 194 mm. Longest dimension 1 436 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Closed container with end doors, 6.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A closed container built from corrugated side and roof sheet on a folded box section frame, with corner castings at every edge and a pair of locking end doors. The doors carry vertical locking bars with cam keepers and hinges, set into a stiffened door frame. It measures about 6.1 m long, 2.4 m wide and 2.6 m high. Parts like this are tacked up on a fixture and welded through, then blasted and painted in the booths on site.
- Length, width and height
- 6 058 x 2 438 x 2 591 mm
- 6 058 x 2 438 x 2 591 mm. Longest dimension 6 058 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Closed machine cabin, 3.8 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A closed machine cabin made from flat welded wall panels with folded edges, standing on base lugs, with a roof of four removable cover panels fitted with lifting handles. One end wall carries a full hinged door, while the opposite corner has a small low hatch opening near the base. It measures about 3.8 by 2.8 m and stands 2.4 m high. Such a part is set on a fixture, tacked and welded out, with every bore and pad cut after welding.
- Length, width and height
- 3 840 x 2 792 x 2 362 mm
- 3 840 x 2 792 x 2 362 mm. Longest dimension 3 840 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Machine house cladding set with louvred panels, 5.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machine house cladding set made from flat steel panels, with louvred vent panels, hinged access doors, inspection hatches, roof edge trim and a base rail. A hopper shaped end panel and rows of fine louvre slats for airflow stand out. It measures about 5.4 by 2.5 m, standing 1.8 m high. A part like this is laser cut up to 20 mm, folded on the 400 t press brake and tack welded on a fixture and welded out.
- Length, width and height
- 5 445 x 2 517 x 1 807 mm
- 5 445 x 2 517 x 1 807 mm. Longest dimension 5 445 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Roll-off container body with hook front, 6.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A roll-off container body is a closed box of corrugated steel sheet on a channel base frame, with ribbed side walls, a slatted roof and roller skids under the rear corners. An upright hook frame with its hook bar sits on the front wall, standing out against the plain corrugated skin. It measures about 6.4 m long, 2.4 m wide and 2.8 m high. Such a part is set on a fixture, tacked and welded out, then finished in the blasting and paint booths on site.
- Length, width and height
- 6 359 x 2 438 x 2 813 mm
- 6 359 x 2 438 x 2 813 mm. Longest dimension 6 359 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Two stacked half-height container units, 6.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A pair of half-height container units stacked on their corner castings, built from corrugated side walls, a plate roof with round ports and folded capping rails. The lower unit has an open end, showing floor framing and a header beam. Overall size is about 6.1 by 2.4 by 2.4 m. Pieces like this are tacked up on a fixture and welded through.
- Length, width and height
- 6 058 x 2 448 x 2 438 mm
- 6 058 x 2 448 x 2 438 mm. Longest dimension 6 058 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Modular building frame, 6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A modular building frame of rectangular hollow section posts and rails, with cross members bracing the open roof and a ribbed floor deck of closely spaced joists below. Corner lugs with bolt holes top each post for stacking or anchoring. It measures about 6.0 by 2.4 m and stands about 2.8 m high. Parts like this are tacked up on a fixture and welded through, then blasted and painted in house.
- Length, width and height
- 5 990 x 2 438 x 2 818 mm
- 5 990 x 2 438 x 2 818 mm. Longest dimension 5 990 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Machine guard enclosure with rounded panels, 5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machine guard enclosure made from curved roof plate, folded side panels and a slender top rail carrying a row of bracket hangers along a long base beam. Each end closes into a rounded hood with cut-out access panels, while the middle section stays open between the two hoods. It measures about 5.0 m long, 1.9 m wide and 1.6 m high. A piece like this is folded over 6 050 mm on the press brake and run on the 14 m robotic welding track when the batch allows.
- Length, width and height
- 5 025 x 1 922 x 1 643 mm
- 5 025 x 1 922 x 1 643 mm. Longest dimension 5 025 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Machine housing with bolted liner plates, 2.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machine housing built from thick folded plate, open at the front with angled side walls and a sloped roof and floor. Liner plates on the roof and floor are held down by rows of bolted pads, with a separate bolt-on door plate at the side and a bored hole in the roof. It measures about 2.2 m long, 1.7 m wide and 1.1 m high. A part like this is tack welded on a fixture and welded out, with the bores and pads machined after welding.
- Length, width and height
- 2 171 x 1 715 x 1 063 mm
- 2 171 x 1 715 x 1 063 mm. Longest dimension 2 171 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Modular building frame with wall studs, 7.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A long box frame built from hollow section posts and rails forms this modular building frame, with both long walls filled by closely spaced vertical studs tied into horizontal ladder rails. Diagonal cross members brace the open roof, and a small mounting bracket sits on the floor rail near one door opening. It measures about 7.5 m long, 3.0 m wide and 3.0 m high. Parts like this are tack welded on a fixture and welded out, then blasted and painted before shipping.
- Length, width and height
- 7 500 x 2 960 x 2 990 mm
- 7 500 x 2 960 x 2 990 mm. Longest dimension 7 500 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Container shell with open end, 12.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A long container shell built from corrugated side plate and a corrugated roof, closed at one end and fully open at the other, with corner posts and corner castings at each edge. The open end exposes a flat floor and frame, with folded corrugation running the full length of sides and roof. It measures about 12.2 m long, 2.4 m wide and 2.6 m high. A part like this is welded out on a fixture.
- Length, width and height
- 12 192 x 2 438 x 2 596 mm
- 12 192 x 2 438 x 2 596 mm. Longest dimension 12 192 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Box body substructure, 7.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A box body substructure is a ladder subframe of two long rails joined by evenly spaced cross members, with a stepped rear cross beam and mounting lugs along both sides. The narrowed rear end and the regular row of cross braces stand out against the otherwise open, flat rails. It measures about 7.4 m long and 1.3 m wide. In this hall a part like this is tacked up on a fixture and welded through, with every bore and pad cut after welding.
- Length, width and height
- 7 400 x 1 258 x 140 mm
- 7 400 x 1 258 x 140 mm. Longest dimension 7 400 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Container steelwork, 6.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A container body made from folded steel plate, with sloped, ribbed side skirts, a flat lipped top edge and a sturdy rear frame around an open bay. Stiffening ribs run along both sides, with pad eyes, lifting brackets and a hinged rear frame standing out. It measures about 6.9 m long, 2.5 m wide and 2.7 m high. Such parts are folded on the press brake and welded on the 14 m robotic track for a series, by hand for a one-off.
- Length, width and height
- 6 901 x 2 508 x 2 651 mm
- 6 901 x 2 508 x 2 651 mm. Longest dimension 6 901 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Welded ladder frame, 6.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welded ladder frame built from two long channel rails joined by a row of narrow cross rungs, with square mounting bores and small brackets spaced along the span. Both rail ends curve upward into a smooth folded lead-in, keeping the deck flush and snag-free. It measures about 6.5 m long, 1.9 m wide and 0.2 m high. Such a part is tack welded on a fixture and welded out, with every bore and pad cut after welding.
- Length, width and height
- 6 545 x 1 940 x 241 mm
- 6 545 x 1 940 x 241 mm. Longest dimension 6 545 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Container body, 6.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A container body made from folded steel plate, with angled skirt panels at each top corner and an open rear end. Vertical ribs divide the sides into panels, each with a horizontal fold line running its length, and the open back shows a sloped floor inside. It measures about 6.4 m long, 2.4 m wide and 2.4 m high. Such parts are folded on the 400 t press brake and run on the 14 m robotic welding track when the batch allows.
- Length, width and height
- 6 407 x 2 418 x 2 382 mm
- 6 407 x 2 418 x 2 382 mm. Longest dimension 6 407 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Roll-off base frame with hook front, 6.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A roll-off base frame of two long box-section rails joined by cross members, with roller brackets at both ends and an upright twin-post hook frame welded to the front. The hook bar sits between the posts above a sloped gusset plate, with small end plates carrying the roller pins. It measures about 6.4 m long, 2.4 m wide and 2.0 m high. Such parts are tacked up on a fixture and welded through, then machined after welding on a horizontal boring mill.
- Length, width and height
- 6 360 x 2 439 x 1 954 mm
- 6 360 x 2 439 x 1 954 mm. Longest dimension 6 360 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Roll-off floor grid with hook front, 6.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A roll-off floor grid built from long side rails and box-section cross members, with two flat plate strips running down the centre and rollers at one end. At the other end stands an upright frame carrying a hook bar for pulling the unit onto a carrier. It measures about 6.4 m long, 2.4 m wide and 2.0 m high. A part like this is tack welded on a fixture and welded out, then blasted and painted in house.
- Length, width and height
- 6 352 x 2 438 x 1 954 mm
- 6 352 x 2 438 x 1 954 mm. Longest dimension 6 352 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Container general arrangement, 6.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
An open-top container body made from flat side and base plate, with vertical external stiffener ribs running the full height down into skid feet. Rear double doors with hinge lugs and a locking bar close one end, a folded top rail edges the open mouth, and a side ladder gives access. It measures about 6.3 m long, 2.6 m wide and 2.8 m high. Such a part is welded out on a fixture.
- Length, width and height
- 6 305 x 2 559 x 2 805 mm
- 6 305 x 2 559 x 2 805 mm. Longest dimension 6 305 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Half-height container unit, 6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A half-height container unit built from corrugated side wall sheeting, a flat sheet roof panel and a welded base frame with corner castings at all eight corners. One end stands open, showing the floor cross members and end frame inside, while the other end is fully closed and plated. It measures about 6.1 by 2.4 m and stands roughly 1.2 m high. A part like this is tack welded on a fixture and welded out, then blasted and painted before shipping.
- Length, width and height
- 6 058 x 2 438 x 1 219 mm
- 6 058 x 2 438 x 1 219 mm. Longest dimension 6 058 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Container body with roof hatch, 6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A roll-off container body built from corrugated side sheet, a flat plate roof and a welded box frame with corner castings at each end. A round bolted hatch sits in the roof, with a ladder and end guides visible at the rear door frame. It measures about 6.1 by 2.4 m and stands about 2.6 m high. A part like this is bent on the 400 t press brake and run on the 14 m robotic welding track when the batch allows.
- Length, width and height
- 6 058 x 2 438 x 2 600 mm
- 6 058 x 2 438 x 2 600 mm. Longest dimension 6 058 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Container floor frame, 6.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A container floor frame built from long side rails in hollow box section, joined by closely spaced cross members and corner castings with bored lugs at each corner. Two plate strips span the width among the cross members, and the rail ends show bored holes for connection. It measures about 6.1 m long, 2.4 m wide and 0.2 m high. Here a part like this is tack welded on a fixture and welded out, then machined after welding on a horizontal boring mill.
- Length, width and height
- 6 058 x 2 438 x 171 mm
- 6 058 x 2 438 x 171 mm. Longest dimension 6 058 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Corrugated roof panel, 6.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A corrugated roof panel for a container structure, a flat sheet of long parallel corrugations set inside a rimmed edge frame. A bored corner casting sits at each corner, with the ribbing running the full length between them. It measures about 6.1 m long by 2.4 m wide and 0.2 m high. Here a part like this is laser cut from plate up to 20 mm, bent on the 400 t press brake and tacked up on a fixture and welded through.
- Length, width and height
- 6 058 x 2 438 x 156 mm
- 6 058 x 2 438 x 156 mm. Longest dimension 6 058 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Platform base frame with corner castings, 6.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A platform base frame built from welded hollow section members, with bored corner castings at each end. Wide bays sit between the cross members, short longitudinal members bridge each bay, and two plate strips run across the middle. The bored castings at the corners stand out, ready for pins or lifting. It measures about 6.1 by 2.4 m and 0.2 m high. Parts like this are set on a fixture, tacked and welded out, with every bore and pad cut after welding.
- Length, width and height
- 6 058 x 2 438 x 173 mm
- 6 058 x 2 438 x 173 mm. Longest dimension 6 058 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Container shell with open end, 6.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A container shell like this is built from corrugated side walls and a corrugated roof panel, framed by a rigid base and top rail with corner castings at every edge. One end is left fully open, with no doors or end frame fitted, showing the plain floor plate inside. It measures about 6.1 m long, 2.4 m wide and 2.6 m high. Parts like this are welded by hand or on the 14 m robotic welding track, with the bores and pads machined after welding.
- Length, width and height
- 6 058 x 2 438 x 2 591 mm
- 6 058 x 2 438 x 2 591 mm. Longest dimension 6 058 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Braced container frame with three bays, 6.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A braced container frame built from hollow section posts and rails, split into three bays by cross frames, with diagonal bracing in the two outer bays and a flat plate floor. Corner castings sit at all eight corners, with ladder-style rung brackets running up two posts. It measures about 6.1 by 2.4 m and stands about 2.6 m high. In this hall a part like this is tack welded on a fixture and welded out, then blasted and painted before shipping.
- Length, width and height
- 6 055 x 2 435 x 2 590 mm
- 6 055 x 2 435 x 2 590 mm. Longest dimension 6 055 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Cabin frame with floor and roof grids, 6.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A cabin frame built from hollow section corner posts and slim intermediate posts, tied together by a floor grid and a roof grid of cross members in matching hollow section. Small mounting plates sit at each corner post base and top. The open box form with its ladder-like floor and roof grids stands out against the bare side walls. It measures about 6.1 by 2.4 by 2.6 m. Here a part like this is tacked up on a fixture and welded through.
- Length, width and height
- 6 055 x 2 440 x 2 591 mm
- 6 055 x 2 440 x 2 591 mm. Longest dimension 6 055 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Wide modular building frame, 6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A wide modular building frame like this is built from hollow box section corner posts and base and top rails, with closely spaced vertical studs and horizontal rails forming each wall into a grid. The roof stays open and the base rail runs flush around all four sides for a floor. It measures about 6.0 by 3.2 m and stands about 3.0 m high. A part like this is welded out on a fixture, then blasted and painted before shipping.
- Length, width and height
- 6 000 x 3 230 x 2 990 mm
- 6 000 x 3 230 x 2 990 mm. Longest dimension 6 000 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Frame with slatted panels, 4.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A frame with slatted panels built from upright box-section posts and top rails, forming a row of standing panels with open bays between them. Two panels carry rows of horizontal slatted plates, while a door frame and narrow plain plate panels close off one end. It measures about 4.7 m long, 0.6 m wide and 2.2 m high. A part like this is tacked up on a fixture and welded through, with every bore and pad cut after welding.
- Length, width and height
- 4 745 x 595 x 2 182 mm
- 4 745 x 595 x 2 182 mm. Longest dimension 4 745 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Hollow section enclosure frame, 4.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
An open enclosure frame built from hollow steel sections, with corner posts, top cross rails and a second ring of rails low near the floor for a future deck. Both views show the same even grid of uprights and horizontals, with no cladding yet, forming a bare cage for walls and floor to be fixed on later. It measures about 4.5 by 2.2 m and stands about 1.0 m high. Such parts are tacked up on a fixture and welded through.
- Length, width and height
- 4 480 x 2 220 x 984 mm
- 4 480 x 2 220 x 984 mm. Longest dimension 4 480 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Machined housing weldment, 3.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machined housing weldment formed from flat steel plate folded into a long narrow box, with top, side and base panels and a flanged base carrying foot tabs. The front wall is pierced with a large round opening, smaller bores and square cut-outs, while internal shelves stiffen the cavity. It measures about 3.3 m long, 1.0 m wide and 1.6 m high. A piece like this is laser cut from plate up to 20 mm and set on a fixture, tacked and welded out.
- Length, width and height
- 3 300 x 955 x 1 575 mm
- 3 300 x 955 x 1 575 mm. Longest dimension 3 300 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Container shell with open sides, 3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A compact container shell takes shape from a corner-post frame, a flat plate roof and a flat plate floor, with corrugated steel sheeting closing one end and one side. Corner castings mark all eight corners, while the long side and the opposite end stand fully open, showing the bare floor plate inside. It measures about 3.0 m long, 2.5 m wide and 2.6 m high. Such a part is welded out on a fixture, then blasted and painted in house.
- Length, width and height
- 2 991 x 2 468 x 2 617 mm
- 2 991 x 2 468 x 2 617 mm. Longest dimension 2 991 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Machine base with panelled walls, 2.8 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A machine base built as a welded box of flat wall panels, open at the top, with corner posts, edge angles and bolted lugs along the top rail. One wall carries a stepped, curved recess near its base, and three post brackets rise above the top edge to carry further structure. It measures about 2.8 by 2.5 by 2.2 m. Such a part is tacked up on a fixture and welded through, then machined after welding on a horizontal boring mill.
- Length, width and height
- 2 777 x 2 485 x 2 190 mm
- 2 777 x 2 485 x 2 190 mm. Longest dimension 2 777 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Open machine guard frame, 2.8 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
An open machine guard frame made from hollow section uprights and rails, forming three open sides with mid rails and a low panelled section along one side, with small brackets and grating panels set into the base. A raking, ladder shaped brace runs up the front, giving access across the frame. It measures about 2.8 m long, 2.1 m wide and 1.9 m high. Here a part like this is set on a fixture, tacked and welded out, then finished in the blasting and paint booths on site.
- Length, width and height
- 2 750 x 2 100 x 1 922 mm
- 2 750 x 2 100 x 1 922 mm. Longest dimension 2 750 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Machine cover tray, 2.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A long, shallow sheet metal tray with low folded side walls and a raised cheek plate at each end, one plate carrying a bored hole and a notched profile. One end has a sloped inner face where the floor steps up to meet the end wall. It measures about 2.7 by 0.9 m, around 0.4 m high. Such a part is cut from plate on the laser bed, bent on the 400 t press brake and welded on the robotic track or by hand.
- Length, width and height
- 2 730 x 935 x 399 mm
- 2 730 x 935 x 399 mm. Longest dimension 2 730 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Machine door frame with three openings, 2.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A folded steel plate frame forms three tall rectangular openings side by side, with angled jambs, a sloped side rib and a small latch box welded along the bottom edge. The flat front face and trapezoidal outline carry mounting bores for hinges and fittings. It measures about 2.2 m long, 0.3 m wide and 1.7 m high. Pieces like this are set on a fixture, tacked and welded out, cut from plate on the laser bed and folded on the 400 t press brake.
- Length, width and height
- 2 174 x 342 x 1 668 mm
- 2 174 x 342 x 1 668 mm. Longest dimension 2 174 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Container door set

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A container door set like this is a flat steel panel with a folded edge frame, two rectangular cut openings of different sizes, and small hinge lugs along one long side. The panel face is plain, with bored corners at each opening and no added ribs. It measures about 2.0 by 0.9 m, around 0.1 m thick. Such a part is tacked up on a fixture and welded through and laser cut from plate up to 20 mm.
- Length, width and height
- 2 040 x 890 x 131 mm
- 2 040 x 890 x 131 mm. Longest dimension 2 040 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Gearbox bridge housing, 1.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A gearbox bridge housing made from two round plated shells with bolt circles, joined by a flat plated bridge and topped with a box-framed deck carrying rib stiffeners. One shell has a bored seat with a shaped cutout, the other a machined mounting rail along its side, with lifting lugs and small access holes in the plate. It measures about 1.6 m long, 1.0 m wide and 1.1 m high. Pieces like this are welded out on a fixture, with every bore and pad cut after welding.
- Length, width and height
- 1 589 x 1 017 x 1 054 mm
- 1 589 x 1 017 x 1 054 mm. Longest dimension 1 589 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Machine cover with ventilation slots, 1.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A closed sheet metal box cover with a flat top, folded side panels and one chamfered corner cut on an angle. Several rows of narrow ventilation slots run along one long side and one end wall, with small bolt holes nearby and a stepped cutout in the top panel. It measures about 1.4 m long, 1.0 m wide and 0.5 m high. Such parts are tacked up on a fixture and welded through and laser cut up to 20 mm.
- Length, width and height
- 1 408 x 1 022 x 454 mm
- 1 408 x 1 022 x 454 mm. Longest dimension 1 408 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Guard cover with ventilation slots, 1.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A guard cover of folded sheet steel, with a low connecting panel linking two raised end boxes, each carrying ventilation slots in its top and side faces. Mounting lugs with bolt holes sit on the outer ends, with fastener holes along the lower edge. It measures about 1.3 m long, 0.5 m wide and 0.4 m high. Pieces like this are laser cut up to 20 mm, folded on the 400 t press brake and set on a fixture, tacked and welded out.
- Length, width and height
- 1 306 x 480 x 351 mm
- 1 306 x 480 x 351 mm. Longest dimension 1 306 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Enclosures and housings
Housing with ring seat, 1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A housing with a ring seat is built up from flat and folded steel plate, forming a tall back wall, side plates and a rounded front tray. An arched cut-out opens the lower front wall, with a bored ring seat inside, stiffening ribs, lugs and rows of drilled holes across the faces. It measures about 1.0 by 0.5 m and stands 0.9 m high. A part like this is tacked up on a fixture and welded through and laser cut from plate up to 20 mm.
- Length, width and height
- 1 000 x 530 x 899 mm
- 1 000 x 530 x 899 mm. Longest dimension 1 000 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Welding jig, 13.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welding jig like this forms a long low fixture bed made from plate and box sections, with rows of clamping lugs, stiffening ribs and locating brackets stepping down its length. A curved frame with a bored eye sits at one end, and a flat machined section with slotted rails runs mid length. It measures about 13.6 m long, 1.6 m wide and 0.6 m high. Here a part like this is tacked up on a fixture and welded through, with the bores and pads machined after welding.
- Length, width and height
- 13 644 x 1 650 x 606 mm
- 13 644 x 1 650 x 606 mm. Longest dimension 13 644 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Welding jig, 8.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welding jig built as a long fixture bed from twin box section beams, carrying rows of clamps, toggle arms, locating pins and adjustable stops, with a smaller clamping frame set beside it. What stands out is the repetition, dozens of matched clamp stations spaced evenly along the bed, each with its own locating lug. It measures about 8.6 m long, 4.1 m wide and 0.6 m high. A piece like this is tacked up on a fixture and welded through, then machined after welding on a horizontal boring mill.
- Length, width and height
- 8 640 x 4 099 x 596 mm
- 8 640 x 4 099 x 596 mm. Longest dimension 8 640 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Transport crate, 4.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A long transport crate built from flat steel plate panels, with a trussed open-grid lid frame, braced end doors and lashing lugs along both lower edges. One end has cross-braced panels, rotary latches and folding casters for towing. It measures about 4.1 m long, 1.4 m wide and 1.2 m high. Such parts are laser cut up to 20 mm, folded on the 400 t press brake and welded by hand or on the 14 m robotic welding track.
- Length, width and height
- 4 061 x 1 393 x 1 220 mm
- 4 061 x 1 393 x 1 220 mm. Longest dimension 4 061 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Tack-welding fixture, 4.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
An octagonal tack-welding fixture built from hollow section rails and uprights, with internal locating frames crossing the ring and stub posts set along the top edge. Short brackets, pads and small bores are fitted into the frame to hold parts square, with projecting corner lugs for clamping on each face. It measures about 4.2 m long, 4.0 m wide and 3.9 m high. In this hall a part like this is welded on the 14 m robotic track for a series, by hand for a one-off.
- Length, width and height
- 4 192 x 4 010 x 3 915 mm
- 4 192 x 4 010 x 3 915 mm. Longest dimension 4 192 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Ring frame, 3.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A ring frame made of two flat steel rings linked by a circle of slim vertical posts and a central post, with bolted pads, bracket lugs and segmented plate joints around both rings. The row of lifting lugs and bolted brackets spaced around the upper ring stands out. It measures about 3.5 m long, 3.4 m wide and 1.5 m high. Parts like this are tacked up on a fixture and welded through, with every bore and pad cut after welding.
- Length, width and height
- 3 520 x 3 449 x 1 510 mm
- 3 520 x 3 449 x 1 510 mm. Longest dimension 3 520 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Lift arm weldment, 2.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A lift arm weldment made from two long parallel box-section arms, cranked down at one end into plate cheeks with pivot bores, tied together by a cross tube and gusset plates, with a hoop bracket and stub lug on top. The cranked, bored plate ends and the welded cross tube stand out. It measures about 2.6 m long, 1.3 m wide and 1.7 m high. Such a part is set on a fixture, tacked and welded out, then machined after welding on a horizontal boring mill.
- Length, width and height
- 2 583 x 1 315 x 1 680 mm
- 2 583 x 1 315 x 1 680 mm. Longest dimension 2 583 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Handling trolley, 1.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A handling trolley built as a welded steel frame on four flanged wheels and two axles, with raked end frames rising to a paired top rail and guide brackets and stub lugs at the corners. The angled end frames and twin top rail stand out above the stiffened deck between the wheel sets. It measures about 1.6 by 1.4 m and stands about 0.9 m high. Such a part is tacked up on a fixture and welded through.
- Length, width and height
- 1 554 x 1 375 x 900 mm
- 1 554 x 1 375 x 900 mm. Longest dimension 1 554 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Hoist frame with hand winch, 2.6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A hoist frame built from a box section upright post carrying a braced triangular jib at the top, formed from flanged box members with a diagonal strut, plus mounting plates with bolt lugs along the post. A hand winch with a crank sits on a side arm, feeding a chain hook that hangs from the jib tip. It stands about 2.4 by 1.4 m and 2.6 m high. Pieces like this are set on a fixture, tacked and welded out, then blasted and painted before shipping.
- Length, width and height
- 2 425 x 1 444 x 2 608 mm
- 2 425 x 1 444 x 2 608 mm. Longest dimension 2 608 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Roll-off body with side doors, 6.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A roll-off body like this is a corrugated steel box on skid rollers, with a ribbed roof, folded side panels and a braced end wall. One side carries hinged doors with slam locks, the other shows the hook lift front with guide channel and roller skid. It measures about 6.4 m long, 2.5 m wide and 2.6 m high. A piece like this is folded on the press brake and run on the 14 m robotic welding track when the batch allows.
- Length, width and height
- 6 363 x 2 525 x 2 555 mm
- 6 363 x 2 525 x 2 555 mm. Longest dimension 6 363 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Scissor arm frame, 6 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A scissor arm frame of this kind is built from two long box section rails joined by cross members, with diagonal bracing and pivot lugs forming an X pattern near both ends. Mid length there are bored pivot seats and a raised bracket pad set between the rails. It measures about 6.0 m long, 1.0 m wide and 0.3 m high. A piece like this is welded out on a fixture, with every bore and pad cut after welding.
- Length, width and height
- 5 989 x 972 x 309 mm
- 5 989 x 972 x 309 mm. Longest dimension 5 989 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Welding jig, 5.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welding jig built as a long two-rail base frame with internal cross members, carrying a row of upright A-frame clamp posts, angled braces and side stops along its full length. The standout feature is the line of swing clamps on tall posts set at even spacing down both rails, holding a workpiece in position. It measures about 5.4 m long, 1.8 m wide and 0.5 m high. Such a part is tacked up on a fixture and welded through, then bored and faced on the boring mill.
- Length, width and height
- 5 395 x 1 810 x 521 mm
- 5 395 x 1 810 x 521 mm. Longest dimension 5 395 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Welding jig, 5.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A long welding jig built as a fixture frame of box section rails and angled plate uprights, braced by diagonal struts and set on levelling feet with base plates. A row of clamp arms with locking handles runs along the top rails, paired with locating pins and small machined seats set between the stiffeners along its length. It measures about 5.3 m long, 1.0 m wide and 1.0 m high. A part like this is set on a fixture, tacked and welded out.
- Length, width and height
- 5 302 x 980 x 982 mm
- 5 302 x 980 x 982 mm. Longest dimension 5 302 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Welding jig, 5.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welding jig built as a long flat base frame of box section rails and cross members, with a row of upright posts fitted with toggle clamps and swinging arms along its length. A repeating line of angled clamp levers and locating lugs holds parts square, with a shaped bracket and small boxed-in fixture at one end. It measures about 5.1 m long, 1.7 m wide and 0.6 m high. Pieces like this are tacked up on a fixture and welded through.
- Length, width and height
- 5 128 x 1 704 x 614 mm
- 5 128 x 1 704 x 614 mm. Longest dimension 5 128 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Welding jig, 4.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welding jig built as a long fixture frame from box section rails and upright legs, with rows of plate brackets, bored lugs and pivot arms spaced along both sides. Swing clamps and locating pins line the rails evenly, ready to hold a workpiece square while it is welded. It measures about 4.4 m long, 1.1 m wide and 0.4 m high. Such a part is welded out on a fixture, then machined after welding on a horizontal boring mill.
- Length, width and height
- 4 386 x 1 094 x 392 mm
- 4 386 x 1 094 x 392 mm. Longest dimension 4 386 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Tack-welding fixture, 4.2 m, variant B

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A tack-welding fixture built as a long plated trough sitting on four box-section legs, with upright clamp posts carrying pivoting clamp arms and diagonal braces tying the legs together. The hopper-shaped plated bed with angled ribs and gusseted corners stands out, forming a defined seat for parts to be positioned and clamped. It measures about 4.1 m long, 2.0 m wide and 1.7 m high. A part like this is set on a fixture, tacked and welded out, then measured with a six-axis measuring arm.
- Length, width and height
- 4 132 x 2 047 x 1 695 mm
- 4 132 x 2 047 x 1 695 mm. Longest dimension 4 132 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Telescopic boom section, 3.8 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A telescopic boom section built from a long welded box section, with top wear plates, internal stiffening ribs, a drilled end collar, a bored pivot head and mounting lugs at the other end. The open box end with its pattern of bolt holes and the machined pivot bores stand out. It measures about 3.8 m long and 0.6 by 0.6 m in section. Parts like this are tack welded on a fixture and welded out, then machined after welding on a horizontal boring mill.
- Length, width and height
- 3 755 x 588 x 560 mm
- 3 755 x 588 x 560 mm. Longest dimension 3 755 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Pattern carrier frame, 3.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A pattern carrier frame is a flat rectangular plate structure with deep side walls, its top divided into six open fields by a grid of cross members. Slotted flange strips run along both long sides, with round bosses set into the end walls and a short center boss standing proud of the grid. It measures about 3.2 by 2.1 m, with a 0.4 m depth. Such a part is tack welded on a fixture and welded out, then machined after welding on a horizontal boring mill.
- Length, width and height
- 3 248 x 2 100 x 434 mm
- 3 248 x 2 100 x 434 mm. Longest dimension 3 248 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Welding jig, 3.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welding jig built on a long base frame of box section beams and angled plate legs, with flat footpads and raised clamp stations along the top rail. A row of adjustable toggle clamps with threaded spindles lines the upper edge, locating parts against folded stops and sloped support plates, with round locating pins at each end. It measures about 3.2 m long, 1.0 m wide and 0.9 m high. Such a part is welded out on a fixture, with the bores and pads machined after welding.
- Length, width and height
- 3 184 x 1 000 x 874 mm
- 3 184 x 1 000 x 874 mm. Longest dimension 3 184 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Foundry flask frame, 3.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A foundry flask frame like this forms a flat rectangular box of deep plate walls, stiffened along both long sides by welded ribs, with two internal cross members dividing the open interior. Folded guide strips run along the top edges, and a round trunnion sits on each short side near a pad with bored holes. It measures about 3.1 by 2.2 m, standing 0.3 m high. Such parts are set on a fixture, tacked and welded out, then bored and faced on the boring mill.
- Length, width and height
- 3 144 x 2 200 x 300 mm
- 3 144 x 2 200 x 300 mm. Longest dimension 3 144 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Boom weldment, 3.1 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A tapered box section boom built from welded plate, with a forked pivot end carrying bored lugs on both sides and a bored eye at the tip. A lug plate sits near the pivot, with stepped plates and stops along the upper flange marking cylinder and hose positions. The forked ends and bored bosses stand out most. It measures about 3.1 m long, 0.7 m wide and 0.8 m high. A piece like this is tacked up on a fixture and welded through.
- Length, width and height
- 3 137 x 650 x 755 mm
- 3 137 x 650 x 755 mm. Longest dimension 3 137 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Slide carriage weldment, 2.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A slide carriage weldment built from a drilled base plate carrying two long parallel box beams, linked by angled ribs, gussets and short upright stiffeners, with web cutouts between them. The plate's bored round seat, square and oval cutouts, bolt pattern lugs and the machined pads along both beam tops stand out. It measures about 2.9 m long, 2.0 m wide and 0.7 m high. In this hall a part like this is tacked up on a fixture and welded through, with every bore and pad cut after welding.
- Length, width and height
- 2 890 x 1 990 x 693 mm
- 2 890 x 1 990 x 693 mm. Longest dimension 2 890 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Comb plate assembly, 2.9 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A comb plate assembly made from a curved upright plate in three joined sections, hooked at both top ends, set on a flat base strip. Triangular gusset ribs run along the back, each with a round bore, with lugs and bolt holes through the base. The hooked, bored, ribbed back stands out. It measures about 2.9 by 0.5 m, standing 1.0 m high. Pieces like this are folded over 6 050 mm on the press brake and welded out on a fixture.
- Length, width and height
- 2 874 x 456 x 1 039 mm
- 2 874 x 456 x 1 039 mm. Longest dimension 2 874 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Press jig, 2.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A press jig built from two long flat plate bars, one carrying five raised locating blocks on angled gussets, the other machined with a central slot and a row of drilled and bored holes along its length. The stops set part position, while the slotted, bored bar guides and locates it beneath. It measures about 2.7 m long, 0.3 m wide and 0.6 m high. Such a part is laser cut from plate up to 20 mm and tack welded on a fixture and welded out.
- Length, width and height
- 2 736 x 280 x 574 mm
- 2 736 x 280 x 574 mm. Longest dimension 2 736 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Swing arm weldment, 2.7 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A swing arm weldment like this is built from two arched side plates joined by cross plates and a connecting tube, with a top plate at the peak and pivot lugs with bored eyes at both feet. The arched profile and paired bores at each end stand out. It measures about 2.7 m long, 0.7 m wide and 1.0 m high. Such a part is cut on the 2 000 x 4 000 mm laser bed, plate up to 20 mm and tacked up on a fixture and welded through.
- Length, width and height
- 2 730 x 728 x 1 022 mm
- 2 730 x 728 x 1 022 mm. Longest dimension 2 730 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Drum body with flanges, 2.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A drum body like this is built from a cylindrical shell with a wide flange at each end, one flange carrying a stepped bore and stub shaft, the other an open bore. Rows of raised lugs run around the shell in staggered bands, with stepped joint lines marking the shell segments along its length. It measures about 2.4 m long and 0.9 by 0.9 m across. Such parts are welded out on a fixture, then bored and faced on the boring mill.
- Length, width and height
- 2 410 x 888 x 888 mm
- 2 410 x 888 x 888 mm. Longest dimension 2 410 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Welding jig with clamps, 2.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welding jig built from a rectangular box section base frame, carrying rows of upright locating plates, angled support posts and gusseted brackets, with toggle clamps mounted on top and slotted holes along the uprights. The mix of tall angled posts and flat plates set out to hold parts from several sides stands out. It measures about 2.2 m long, 1.7 m wide and 0.6 m high. Such parts are set on a fixture, tacked and welded out.
- Length, width and height
- 2 167 x 1 660 x 637 mm
- 2 167 x 1 660 x 637 mm. Longest dimension 2 167 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Perforated tube plate, 1.5 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A thick round steel plate with a bolt hole ring at the rim and segmented fields of closely drilled tube holes across the face, divided by plain bands into wedge sections. The dense, even pattern of bores stands out, framed by a clean machined outer edge. It measures about 1.5 by 1.5 m, 0.1 m thick. Parts like this are laser cut from plate up to 20 mm, tack welded on a fixture and welded out, with the bores and pads machined after welding.
- Length, width and height
- 1 540 x 54 x 1 540 mm
- 1 540 x 54 x 1 540 mm. Longest dimension 1 540 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Welding jig, 1.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welding jig built as a plate and box section bed with upright posts, cross beams and diagonal ribs, fitted with screw clamps, curved hooked locating arms and flat stop plates. What stands out is the row of threaded clamp spindles with handwheels facing across the bed, plus the hooked arms swinging in to hold the work. It measures about 1.4 m long, 1.1 m wide and 0.5 m high. A part like this is tacked up on a fixture and welded through.
- Length, width and height
- 1 442 x 1 134 x 508 mm
- 1 442 x 1 134 x 508 mm. Longest dimension 1 442 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Lever pair with cross tube, 1.4 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A lever pair like this is formed from two tapered plate arms joined by a long cross tube, with bored pivot holes at top and bottom and a small welded hoop lug on one lever. The faceted, planed plate faces and the machined bores where the tube meets each lever stand out. It measures about 1.4 m long, 0.5 m wide and 0.7 m high. Parts like this are tack welded on a fixture and welded out, with every bore and pad cut after welding.
- Length, width and height
- 1 361 x 454 x 699 mm
- 1 361 x 454 x 699 mm. Longest dimension 1 361 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Bearing plate with flange ring, 1.3 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A bearing plate like this is a square drilled plate with a raised round flange ring welded at its centre, stepped down in two tiers, with three round bosses and a pair of triangular lifting lugs across one edge. The machined bore in the flange ring and the bolt circle of drilled holes around it stand out. It measures about 1.3 by 1.3 m, and about 0.2 m high. Parts like this are set on a fixture, tacked and welded out.
- Length, width and height
- 1 310 x 1 300 x 222 mm
- 1 310 x 1 300 x 222 mm. Longest dimension 1 310 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Welding jig, 1.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A welding jig built on two channel base rails, with an upper frame of box section uprights, flat bars and lugged brackets tying it together. Screw clamps with handled spindles and a pivoting locator with a bored seat clamp and position parts for tacking. Bored pads and machined seats mark the locating points on both sides. It measures about 1.2 by 1.0 m and stands 0.4 m high. Parts like this are set on a fixture, tacked and welded out, then bored and faced on the boring mill.
- Length, width and height
- 1 243 x 1 042 x 403 mm
- 1 243 x 1 042 x 403 mm. Longest dimension 1 243 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Built to your drawing
Heavy bracket weldment with lugs, 1.2 m

Rendered here from the structure's own geometry. No model file is served from this site.
What it is
A heavy bracket weldment built from two tall, curved cheek plates with rounded tops and lightening holes, joined by a bored cross tube, a drilled deck plate and gusseted ribs down to a flat base with ring lugs and bolt holes. The bored pivot seat at the top and the flared base lugs stand out. It measures about 1.1 by 0.9 m and stands 1.2 m high. Such a part is laser cut up to 20 mm and welded out on a fixture.
- Length, width and height
- 1 089 x 930 x 1 243 mm
- 1 089 x 930 x 1 243 mm. Longest dimension 1 243 mm, measured from the geometry.
Similar models
Customer names, machine designations and drawing numbers are not published, and part lists and files are not offered. What is shown is the steel, its measured size and the group it belongs to.
Start here
Send the drawing. We answer with a price and a date.
STEP, DWG, DXF, PDF or ZIP, up to five files. Your drawings stay private: they are stored outside the web server and read only by our engineers.






























































































































































































